Broadcom NetXtreme II SERIES Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 264

background image

iSCSI Protocol: Broadcom NetXtreme II® Network Adapter User Guide

file:///C|/Users/Nalina_N_S/Documents/NetXtremeII/English/iscsi.htm[9/5/2014 3:45:06 PM]

Back to Contents Page

iSCSI Protocol: Broadcom NetXtreme II

®

Network Adapter User

Guide

iSCSI Boot

iSCSI Crash Dump

iSCSI Offload in Windows Server

iSCSI Boot

Broadcom NetXtreme II Gigabit Ethernet adapters support iSCSI boot to enable network boot of operating systems to diskless
systems. iSCSI boot allows a Windows, Linux, or VMware operating system boot from an iSCSI target machine located
remotely over a standard IP network.

For both Windows and Linux operating systems, iSCSI boot can be configured to boot with two distinctive paths: non-offload
(also known as Microsoft/Open-iSCSI initiator) and offload (Broadcom's offload iSCSI driver or HBA). Configuration of the
path is set with the

HBA Boot Mode

option located on the

General Parameters

screen of the iSCSI Configuration utility.

See

Table 1

for more information on all

General Parameters

screen configuration options.

Supported Operating Systems for iSCSI Boot

The Broadcom NetXtreme II Gigabit Ethernet adapters support iSCSI boot on the following operating systems:

Windows Server 2008 and later 32-bit and 64-bit (supports offload and non-offload paths)
Linux RHEL 5.5 and later, SLES 11.1 and later (supports offload and non-offload paths)
SLES 10.x and SLES 11 (only supports non-offload path)

iSCSI Boot Setup

The iSCSI boot setup consists of:

Configuring the iSCSI Target
Configuring iSCSI Boot Parameters
Preparing the iSCSI Boot Image
Booting

Configuring the iSCSI Target

Configuring the iSCSI target varies by target vendors. For information on configuring the iSCSI target, refer to the
documentation provided by the vendor. The general steps include:

1.  Create an iSCSI target.
2.  Create a virtual disk.
3.  Map the virtual disk to the iSCSI target created in step 1.
4.  Associate an iSCSI initiator with the iSCSI target.
5.  Record the iSCSI target name, TCP port number, iSCSI Logical Unit Number (LUN), initiator Internet Qualified Name

(IQN), and CHAP authentication details.

6. After configuring the iSCSI target, obtain the following:

Target IQN
Target IP address
Target TCP port number
Target LUN

«
...
73
74
75
76
77
...
»

Содержание NetXtreme II SERIES









































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NetXtreme II SERIES

Бренд: LaCie Страницы: 44

LaCie Ethernet Disk

Бренд: LaCie Страницы: 2

12big Rack Fibre 8

Бренд: LaCie Страницы: 9

8677 - BladeCenter Rack-mountable - Power...

Бренд: IBM Страницы: 126

Бренд: Javad Страницы: 35

Бренд: Campbell Страницы: 38

Бренд: WAGO Страницы: 48

Бренд: TP-Link Страницы: 2

Бренд: ADTRAN Страницы: 9

Бренд: Amit Страницы: 75

CloudGen Firewall

Бренд: Barracuda Страницы: 8

Broadband 700 MHz

Бренд: Alcatel-Lucent Страницы: 8

Бренд: Radio Shack Страницы: 40

Бренд: Geneko Страницы: 8

Бренд: NETGEAR Страницы: 2

Бренд: Billion Страницы: 183

Бренд: Billion Страницы: 20

Бренд: Dell Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды