Broadcom NetXtreme Ethernet Adapter • Diagnostic User’s Guide
page 141
Broadcom Confidential and Proprietary
/* ERR_GPIO5704 102 */ "Dev:%d Expected GPIO 0/1/2 = %d/%d/%d, but read as
%d/%d/%d",
/* ERR_BIST_NOT_DONE 103 */ "Bist test did not complete internally",
/* ERR_BIST_DATA_MISCMP 104 */ "Bist data miscompared at bit: %d out: %d exp: %d",
/* ERR_CPU_NO_RESPONSE 105 */ "No Response from firmware",
/* ERR_CPU_ERR_CODE 106 */ "%s CPU returned result %d, key = %d",
/* CMD_LOOP 107 */ "",
/* CMD_SKIP 108 */ "",
/* CMD_ELSE, 109 */ "",
/* CMD_ELSEIF, 110 */ "",
/* CMD_BREAK, 111 */ "",
/* CMD_ENDWHILE, 112 */ "",
/* ERR_BYTE, 113 */ "Byte access error: expected %02x at %08x but got %02x",
/* ERR_WORD, 114 */ "Wrd acc err: exp %04x at %08x but got %04x (need
flshdg5x.bin v2.3 or newer)",
/* ERR_NO_LINK_DOWN 115 */ "No link down found",
/* ERR_MISMATCHED_DEVICEID 116 */ "bootcode Image file belongs to %d family, does not
match with board %d",
/* ERR_INVALID_DATA_SIZE 117 */ "Invalid data size",
/* ERR_MAC_ADDR_ENDED 118 */ "Runs out of Mac Address",
/* ERR_ILLEGAL_MAC_ADDR 119 */ "Illegal Mac Address",
/* ERR_BIST_DATA_INVALID 120 */ "Invalid bist data from buffer at %d",
/* ERR_INVALID_BOND_ID 121 */ "Invalid bond id",
/* ERR_BAD_CPU_RESET 122 */ "CPU reset failed, register 5034 is 0x%x",
/* ERR_INCORRECT_VERSION 123 */ "Incorrect version",
/* ERR_MISMATCH_CFG_VERSION 124 */ "Mismatched CFG and FW Image version",
/* ERR_NOT_SUPP_CFG_BW 125 */ "Current ASF_T_VERSION is not backward compatible",
/* ERR_POST_1G_LB 126 */ "1G Tx/Rx Lines Have A Short/Open",
/* ERR_DRIVER 127 */ "Driver %d.%d.%d or later is required to run this
function",
/* ERR_TXDMA_OVERFLOW 128 */ "TxDMA Overflow",
/* ERR_RXDMA_OVERFLOW 129 */ "RxDMA Overflow",
/* ERR_DRIVER_BAD_STATUS 130 */ "Driver returned error status=%d",
/* ERR_INVALID_HANDLE 131 */ "Invalid Handle",
/* ERR_SOCKET 132 */ "Socket open error%d %s",
/* ERR_SIOCGIFINDEX 133 */ "ioctl(): SIOCGIFINDEX failed",
/* ERR_BIND 134 */ "bind() failed: %s",
/* ERR_SETSOCKOPT 135 */ "setsockopt() failed:%d %s",
/* ERR_FCNTL 136 */ "fcntl() failed:%d %s",
/* ERR_SEND 137 */ "send() failed (cnt=%d): %d %s",
/* ERR_RECEIVE 138 */ "recvfrom() failed (cnt=%d): %d %s",
/* ERR_FALSE_CARRIER 139 */ "Error! False Carrier Detected During The Test",
/* ERR_INV_OPT 140 */ "Invalid Options",
/* ERR_INV_DEV 141 */ "Found Rv = %s, Expected Rv = %s due to -ckdev value",
/* ERR_IRQ 142 */ "Invalid IRQ %d",
/* ERR_TIMEOUT 143 */ "Timeout",
/* ERR_PKT_DATA 144 */ "Packet data error at offset %d, expected %02X but
recevied %02X",
/* ERR_MAC_ZERO 145 */ "Zero Mac Address in Mac Register",
/* ERR_MAC_MIS_REG 146 */ "Mac Address MisMatch: Got %02X-%02X-%02X-%02X-%02X-
%02X.",
/* ERR_CPU_ACC 147 */ "%cx CPU failed on %s bit access to address %08X",
/* ERR_CPU_MEM 148 */ "%cx CPU failed on memory pattern %08X at address %08X",
/* ERR_CPU_INSTR 149 */ "%cx CPU Instruction test failed",
/* ERR_BUS_LINK 150 */ "PCI-E Bus Link Error",
/* ERR_ASF_FILE_VER 151 */ "ASF File versions Error",
/* ERR_ASF_VS_DEV 152 */ "ASF VS Device Error",
/* ERR_MISMATCHED_DEVICEID_1 153 */ "bootcode Image file belongs to unknown family, does
not match with board %d",
/* ERR_MISMATCHED_DEVICEID_2 154 */ "bootcode Image file belongs to %d family, does not
match with unknown board",
/* ERR_CPU_FETCH 155 */ "CPU Fetch Test Error: Breakpoint reads %x",
/* ERR_UMPLB 156 */ "UMP loopback failed, Total Good packet %d",
/* ERR_UMPCTRL 157 */ "Error: UMPCtrl 0x5F0 = %x",
/* ERR_REG_TABLE 158 */ "Error: Unable to create Reg Table",
/* ERR_FW_IMAGE_SIZE 159 */ "Error: Firmware image size (%d) larger than NVRAM
size (%d)",
/* ERR_MISS_PXE 160 */ "Error: %s firmware cannot be found in %s",
/* ERR_MISS_ASF 161 */ "Error: %s firmware cannot be found in %s",
/* ERR_NVRAM_DIR 162 */ "Error: NVRAM Directory",
/* ERR_MISS_UMP 163 */ "Error: %s firmware cannot be found in %s",
