BRITEQ®
19
BTX-700SW
R-Prism
—
Prism rotation home position adjust
Enter offset mode, Select
R-Prism
, press ENTER button to confirm, the present position
will blink on the display, use UP and DOWN button to offset the value from -128 to 127,
press ENTER button to store. Press MENU button to exit.
Frost
—
Frost home position adjust
Enter offset mode, Select
Frost
, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Flatb
—
Flatb home position adjust
Enter offset mode, Select
Flatb
, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Focus
—
Focus home position adjust
Enter offset mode, Select
Focus
, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
Zoom
—
Zoom home position adjust
Enter offset mode, Select
Zoom
, press ENTER button to confirm, the present position will
blink on the display, use UP and DOWN button to offset the value from 0 to 255, press
ENTER button to store. Press MENU button to exit.
6.4. Error Information
Lamp Startup Fail
It appears when there is no lamp or some wires are damaged.
Temperature Sense Error
It appears when temperature check board is damaged.
Lamp Too Hot Power Off
It appears when temperature is detected higher than 110
℃
. Check if the unit is properly
ventilated, or fans or temperature check board may is damaged.
Lamp Too Hot Low Power
It appears when detected temperature is over 105
℃
. the unit will run on a low power level.
Maintenance Fixture
It appears when the maintenance remaining time becomes 0S, please enter menu mode
and reset the time.
Lamp On Over 700 Hour
It appears when the lamp has been on over 700 hours, please turn off the lamp.
Memory Initial Fail
It appears when the memory IC is damaged.
CPU-B Error, CPU-C Error, CPU-D Error
They appear when board P.C or some wires are damaged.
Pan Reset Error, Pan Encode Error, Tilt Reset Error, Tilt Encode Error, Shutter Reset
Fail, Dimmer Reset Fail, Color Reset Fail, Cyan Reset Fail, Magenta Reset Fail, Yellow
Reset Fail, Gobo1 Reset Fail, R-Gobo1 Reset Fail, Gobo2 Reset Fail, Iris Reset Fail,
Effect Reset Fail, R-Effect Reset Fail, Frost Reset Fail, Flatb Reset Fail, Focus Reset
Fail, Zoom Reset Fail
They may appear when turn on or reset the unit, for some parts such as board P.C are
damaged. Please contact the qualified maintenance.
BRITEQ®
20
BTX-700SW
7. Control By Universal DMX Controller
7.1 Connection
1.At last unit, the DMX cable has to be terminated with a terminator. Solder a 120-ohm
1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in
the DMX-output of the last unit.
2.Connect the unit together in a “daisy chain” by XLR plug cable from the output of the unit
to the input of the next unit. The cable cannot be branched or split to a “Y” cable. DMX
512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or
corroded connectors can easily distort the signal and shut down the system.
3.The DMX output and input connectors are pass-through to maintain the DMX circuit,
when one of the units’ power is disconnected.
4.Each lighting unit needs to have a DMX address to receive the data by the controller. The
address number is between 0-511 (usually 0 & 1 are equal to 1).
5.The end of the DMX 512 system should be terminated to reduce signal errors.
6.3 pin XLR connectors are more popular than 5 pins XLR.
3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+)
5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+), Pin4, Pin5 not
used.
ATTENTION
Termination reduces signal errors and to avoid signal transmission
problems and interference. It is always advisable to connect a DMX terminal
(Resistance 120 ohm 1/4W between pin2 (DMX-) and pin3 (DMX+) of the last
