Not for
Reproduction
14
NOTICE:
Do not allow grease or oil to contact the rubber
friction wheel or the disc drive plate. If grease or oil comes
into contact with the friction wheel, replace it. Do not attempt
to clean it. If grease or oil comes into contact with disc drive
plate, clean it thoroughly with an alcohol based solvent.
1. Position speed select lever in the first forward gear.
2. Drain fuel to an approved container.
Hex Shaft and Gear Lubrication
3. Stand the snowthrower up on the auger housing end.
NOTE: When the crankcase is filled with oil, do not leave
the snowthrower standing up on the auger housing for an
extended period of time.
4. Remove screws (A, Figure 9) and bottom panel (B).
5. Wipe the hex shaft (C, Figure 10) with 5W30 synthetic
motor oil, before storage and at the beginning of each
season.
6. Install the bottom panel (B, Figure 9) and screws (A).
WARNING
Fire and explosion hazard
Gasoline is highly flammable and its vapors are explosive.
Drain gasoline outdoors, away from fire and other ignition
sources. Wipe up any spills immediately. Do NOT allow
open flame, smoking, or matches in the area.
NOTE: If the auger or traction cables become stretched or
are sagging, adjustment is necessary.
1. Loosen finger nut (A, Figure 11).
2. Hold control cable (B) to keep it from rotating.
NOTE: The cable should not rotate while making adjustment.
3. Turn collar (C) to remove slack but do not over-tighten.
4. Tighten finger nut.
5. Perform snowthrower safety test to ensure proper opera-
tion. See
Safety System Tests
.
If necessary, make addi-
tional adjustments.
Auger and Traction Cable Adjustment
DANGER
Amputation hazard
Over-tightening the auger cable may cause the auger drive
to engage without depressing the auger drive control.
Follow the adjustment procedure to ensure the cable is not
over-tightened.
If the speed control rod requires adjustment, see an autho-
rized dealer.
Speed Control Rod Adjustment
Tire pressure should be checked periodically. The maximum
tire pressure is stamped on the sidewall of the tires. Do not
exceed this pressure.
Checking Tire Pressure
WARNING
Explosion hazard
Over-inflation of tires may cause them to explode, which
could result in serious injury.
Do not inflate the tires above the maximum pressure.
Содержание S1024MD
