manualshive.com logo in svg

Breckwell SPC50, Руководство по установке, Страница: 22 / 28

Поделиться
Скачать
Breckwell SPC50 Скачать руководство пользователя страница 22

22 

PARTS LIST

Part No.

Description

Qty.

892300

Main Stove Body (Specify Color)

1

40599

Legs (Specify Color)

4

892301

Front Door Assembly (Specify Color)

1

40600

Front Door (Specify Color)

1

892302

Glass

1

88087

Glass Gasket 

1

88066

Door Gasket 

1

892303

Glass Retainers

7

892304

Hinge Pins

2

892308

Handle Assembly

1

892305

Cam

1

892306

Plastic Knob

1

892307

Brass Handle Body W/ Stud

1

892309

Side Door Assembly (Specify Color)

1

40601

Side Door (Specify Color)

1

892310

Handle

1

892311

Hinge Pins

2

88033

Rope Gasket

1

892312

Handle Catch

1

892319

Auger Assembly

1

892321

Auger Body

1

892322

Auger

1

892320

Auger Bushing/Bearing Assembly

1

40602

Baf

fl

 es

2

892314

Primary/Secondary Air Tube Assembly 1

892315

Tube Weldment

1

892316

Primary Air Bushing

1

892317

Primary Air Nozzle

1

892318

Air Shutter Assembly

1

892313

Touchup Paint    (Specify Color)

1

80664

4” Fan

2

80665

Electromagnet 12-Volt

1

80491

Microswitch

1

80661

Pressure Switch

1

80663

Hopper Thermodisc

1

80462

Receptacle, 3-Prong

1

80461

Cord, 3-Prong

1

80249

Burn Back Thermodisc

1

80610

Proof of Fire Thermodisc

1

80462

Auger Motor

1

892325

Fan Cover Grill

1

IN ORDER TO MAINTAIN WARRANTY, COMPONENTS MUST BE REPLACED USING ORIGINAL 

MANUFACTURERS PARTS PURCHASED THROUGH YOUR DEALER OR DIRECTLY FROM THE 

APPLIANCE MANUFACTURER. 

USE OF THIRD PARTY COMPONENTS WILL VOID THE WARRANTY.

Содержание SPC50





























Отзывы:

Нет отзывов