manualshive.com logo in svg

Breckwell SPC50, Руководство по установке, Страница: 21 / 28

Поделиться
Скачать
Breckwell SPC50 Скачать руководство пользователя страница 21

 

21

TROUBLE SHOOTING GUIDE

BLOWER

The gasket on the blower has gone bad.

Inspect both gaskets on the combustion blower to make sure 

they are in good shape. Replace if damaged.

The blower is overheating and tripping the internal temperature 

shutoff.

Clean any dust off of the windings and fan blades.  If cleaning 

the blower does not help, the blower may be bad.

Blower failure.

With the stove on, check to see if the blower is running. If it 

is not, you will need to check for power going to the blower. It 
should be a full current. If there is power, the blower is bad. If 
there is not the control board may be malfunctioning.

WIRING & CONTROLS

Circuit board malfunction.

Test the current going to the convection blower.  If there is 

power being sent to the blower when it is shut off, then the control 
board is 

fi

 ne.  If there is not power being sent to the blower when 

it shuts off during operation, then you have a bad control board.

7. Control board not sending power to combustion blower.

If there is no current going to the combustion blower, check all 

wire connections. If all wires are properly connected, you have 
a bad control board.

9. Air switch has failed.

To test the air switch, you will need to disconnect the air hose 

from the body of the stove. With the other end still attached to 
the air switch, very gently blow on the loose end of the hose 
(you may want to remove the hose entirely off the stove and the 
air switch 

fi

 rst and make sure it is clear). If you hear a click, the 

air switch is working. Be careful too much vacuum can damage 
the air switch.

1. Air

fl

 ow switch hose or stove attachment pipes for hose are 

blocked.

Unhook air hose from the air switch and blow through it. If air 

fl

 ows freely, the hose and tube are 

fi

 ne. If air will not 

fl

 ow throw 

the hose, use a wire coat hanger to clear the blockage.

5. The air

fl

 ow switch wire connections are bad.

Check the connectors that attach the blue wires to the air switch.

8. Control board not sending power to air switch.

There should be a 5-volt current (approximately) going to the 

air switch after the stove has been on for 30 seconds.

Содержание SPC50





























Отзывы:

Нет отзывов