Breckwell SPC50 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 28

Breckwell SPC50 Скачать руководство пользователя страница 12

12

THERMOSTAT INSTALLATION & OPERATION

THERMOSTAT REQUIREMENTS

The will accept a non-voltage carrying thermostat.

Do not use a thermostat with a transformer

THERMOSTAT INSTALLATION

1.  Unplug the stove.
2.  Remove controller from the stove.
3.  Remove the black jumper from J8.
4.  Attach the thermostat wires to the blue TSTAT Terminal.

THERMOSTAT OPERATION

After the stove is running when the thermostat calls for heat the heat level will go to the level that you set on the controller. It is

recommended that you set the heat level to slightly above what is needed. When the thermostat is satis

fi

ed then the stove will return

to idle until heat is called for again.

TO ADJUST THE THERMOSTAT IDLE HEAT LEVEL

1.  When the stove is in run mode, scroll through the main menu until you see “set idle heat level”.
2.  Press enter to select.
3.  Use the left and right arrows to adjust the temperature, just as up would control the standard heat level.
4.  Press menu to return to standard operation, or it will time out after a few seconds.

«
...
10
11
12
13
14
...
»

Содержание SPC50





























Отзывы:

Нет отзывов