Bray 19L Series Скачать руководство пользователя страница 29

Страница: 29 / 31

FLOW-TEK SERIES 19L SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

29 of 31

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

17.0 RETURN MERCHANDISE AUTHORIZATION

17.1

All products that are returned require a Return Merchandise
Authorization (RMA). Contact a Bray representative for instructions
and RMA forms to be completed prior to return of any product.

17.2

The following information must be provided when submitting RMA.

> Serial number

> Part number

> Month and year of manufacture

> Actuator specifics

> Application

> Media

> Operating temperature

> Operating pressure

> Total estimated cycles (since last installation or repair)

NOTE

: Product information is provided on identification tag

attached to device.

NOTICE

Materials must be cleaned and sanitized prior to return. MSDS
sheets and Declaration of Decontamination are required.

Содержание 19L Series
































Результаты поиска

Содержание 19L Series

Отзывы:

Бренды по названию

Популярные бренды

Bray 19L Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 19L Series

Отзывы:

Бренды по названию

Популярные бренды