Bray 19L Series Скачать руководство пользователя страница 22

Страница: 22 / 31

FLOW-TEK SERIES 19L SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

22 of 31

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

13.2

Installing the Seat & Liner

CAUTION

Be extremely careful not to gall or scratch the sealing surface of
the seat. Scratches may later cause excessive leakage and seal
wear.

When used, solid tungsten carbide seats and liners should be
handled with care, avoiding impact or excessive loads, to prevent
damage.

13.2.1 Ensure the segment is in the fully closed position. Insert the seat

through the downstream bore (with the seal surface facing the
segment) until the seat contacts the segment.

13.2.2 Select seat seal guide (not shown) from

Table 3

, based on valve

size. Place the seat seal guide on the seat. Insert springs and seat
seal with guide washers on each side.

13.2.3 Insert liner, retainer gasket, and liner retainer onto body.

13.2.4 Use hydraulic press against liner retainer to compress liner and

seat seal assembly until the liner retainer contacts body end
flange. (Use loads shown in

Table 4

13.2.5 Install retainer screws and hand tighten. (Ensure the seat seal

guide is removed after the liner retainer screws have been
installed.)

NOTICE

Retainer screws are designed for retention only. Retainer gasket
will be compressed by tightening of the end flange bolting.

13.3

Shell and Seat Test

13.3.1 After reassembly, perform a shell and seat test to ensure proper

operation.

Figure 3:

Installing the seat and

liner.

Содержание 19L Series
































Результаты поиска

Содержание 19L Series

Отзывы:

Бренды по названию

Популярные бренды

Bray 19L Series, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 19L Series

Отзывы:

Бренды по названию

Популярные бренды