manualshive.com logo in svg

Bray 19L Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Bray 19L Series Скачать руководство пользователя страница 20

FLOW-TEK SERIES 19L SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

20 of 31

© 2021 BRAY INTERNATIONAL, INC. ALL RIGHTS RESERVED. BRAY.COM   The Information 

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would 

violate its proprietary nature without the express written permission of Bray International, Inc.

12.0  REMOVING VALVE FROM PIPELINE

12.1

If an internal problem is suspected with the valve and disassembly 
is required, remove the valve from the pipeline by proceeding as 
follows.

WARNING

Depressurize line to atmospheric pressure, drain all process fluids 
and decontaminate the valve (if caustic or hazardous materials 
are present). Failure to do so can cause serious injury. 

Make sure the valve is in closed position.

12.2

Neutralize all energy (electrical, pressure and mechanical) 
sources. 

12.3

Attach a hoist or some means to support the valve.

12.4

Remove line bolting.

CAUTION

Do not attempt to pry line flanges apart by pushing or pulling on 
the valve or actuator.

12.5

Slide the valve carefully from the pipeline. 

CAUTION

To avoid damage to the gasket surfaces, do not twist the valve.

12.6

After the valve is completely removed from the line, slowly relieve 
actuating medium pressure from the actuator.

WARNING

Ensure hands and/or any other items are removed from the bore 
of the valve.

Содержание 19L Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды