Bray 19L Series Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

background image

FLOW-TEK SERIES 19L SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

17 of 31

© 2021 BRAY INTERNATIONAL, INC. ALL RIGHTS RESERVED. BRAY.COM The Information

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would

violate its proprietary nature without the express written permission of Bray International, Inc.

9.0 OPERATION

9.1

Operation

Operation of the valve is done by turning the stem a quarter-turn
(90 degree turn).

> The stem is turned clockwise to close, counter-clockwise to

open.

9.2

Indication

The valve open and closed position are indicated by the position
of indentation on the stem.

> Valve

OPEN

position: Flats of Double-D stem are

parallel

to

pipeline.

> Valve

CLOSED

position: Flats of Double-D stem are

perpedicular

to pipeline.

CAUTION

Valves with actuators should be inspected for actuator/valve
alignment. Misalignment will result in high operational torque and
damage to valve stem and seals.

OPEN

CLOSED

Stem

Indentation

Stem

Indentation

Figure 1:

Indication of valve

Open and Closed position.

«
...
15
16
17
18
19
...
»

Содержание 19L Series
































Отзывы:

Нет отзывов

Похожие инструкции для 19L Series

Бренд: Haier Страницы: 58

Бренд: Access Страницы: 12

Pulsafeeder MPC Vector

Бренд: Idex Страницы: 114

Бренд: Trane Страницы: 72

Бренд: Yolink Страницы: 23

Бренд: UUGear Страницы: 38

Бренд: DNF Controls Страницы: 22

Бренд: Matelec Страницы: 2

Бренд: Casambi Страницы: 4

Бренд: Castell Страницы: 7

Бренд: B&B Molders Страницы: 18

Бренд: BENSHAW Страницы: 16

Бренд: DAAB Страницы: 60

Бренд: BILDA Страницы: 2

MCE Lasers DUO 2 v2

Бренд: MOBA Страницы: 60

Бренд: Madas Страницы: 58

AeGIS 9100CR200

Бренд: PACH & COMPANY Страницы: 49

Verafix-Cool V9406

Бренд: Honeywell Home Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды