manualshive.com logo in svg

Bray 19L Series, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Bray 19L Series Скачать руководство пользователя страница 19

FLOW-TEK SERIES 19L SEGMENTED BALL VALVE

Installation, Operation, and Maintenance Manual

19 of 31

© 2021 BRAY INTERNATIONAL, INC. ALL RIGHTS RESERVED. BRAY.COM   The Information 

contained herein shall not be copied, transferred, conveyed, or displayed in any manner that would 

violate its proprietary nature without the express written permission of Bray International, Inc.

11.0 

ACTUATOR REMOVAL AND REMOUNTING

11.1

Removing Actuator 

11.1.1 Refer to relevant actuator installation, operation, and 

maintenance instructions before proceeding.

11.1.2 Neutralize all energy sources (electrical, pressure and 

mechanical).

11.1.3 Support the actuator assembly before disconnecting it from the 

body assembly. 

11.1.4 Unbolt the actuator assembly from valve mounting bracket.

11.1.5 Lift actuator assembly off stem.

11.2

Remounting Actuator

11.2.1 Before mounting an actuator on the valve body, verify that the 

segment rotation matches the actuator rotation and complies 
with the actuator failure mode requirements. 

11.2.2 Bolt the bracket onto the body (if it has been removed.)

11.2.3 Slide the entire actuator assembly onto the stem. 

11.2.4 Bolt actuator assembly to valve mounting bracket.

11.2.5 Verify and set actuator stops..

NOTICE

Refer to the actuator IOM for necessary adjustments.

Содержание 19L Series
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды