Brave VH1724GC страница 55 Скачать руководство пользователя

Страница: 55 / 62

Assembly Instructions

Tools Needed



(2) Adjustable
Wrenches



Pliers

Step 17 – High Pressure Hose



Remove hose with fittings and sleeving from hose guides.



Remove plastic plug from pump outlet with pliers (plastic plug is the
outer most fitting).



Screw hand-tight high pressure hose to the pump outlet.



Wrench-tighten the fitting to 1.5-3.0 Turns Past Finger Tight position.
Properly assembled fittings total thread engagement should be 3.5-6
turns.



Route hose back through hose guides, with hose as far down on the
beam as possible (high pressure hose will be routed on the bottom).



Screw finger-tight remaining end of the High-Pressure Supply Hose to
the Valve Inlet Fitting on the control valve inlet.



Wrench-tighten the fitting.

Pump
Outlet

High-Pressure

Supply Hose

Hose Guide

Valve Inlet
Fitting

Содержание VH1724GC































































Результаты поиска

Содержание VH1724GC

Отзывы:

Похожие инструкции для VH1724GC

Бренды по названию

Популярные бренды

Brave VH1724GC, Руководство пользователя

Результаты поиска

Содержание VH1724GC

Отзывы:

Похожие инструкции для VH1724GC

Бренды по названию

Популярные бренды