Brave VH1724GC Скачать руководство пользователя страница 52

Страница: 52 / 62

Assembly Instructions

Step 14 – Install Cylinder Hose Fitting



Lubricate O-ring and threads on fitting with clean oil.



Looking at fitting from end with nut/washer/O-ring assembly, turn nut
clockwise as far as possible.



Using wrench, turn (1) cylinder hose fitting into valve port marked
“B” until washer touches control valve. Continue turning until washer
touches thread nearest wrench pad.



Back off fitting counterclockwise not exceeding one revolution until it
is oriented in the correct position, at a 90° angle.



Place wrench on the wrench pad of fitting to prevent fitting from
turning and torque nut to 37-46 ft.-lb.

Tools Needed



(2) Adjustable
Wrenches



Torque Wrench



22mm Crowfoot
Wrench

Part # 778827

Cylinder Hose Fitting

Qty: 1

Fitting Needed from Parts Bag:

Wrench Pad

Nut/Washer/O-ring Assembly

Содержание VH1724GC































































Результаты поиска

Содержание VH1724GC

Отзывы:

Бренды по названию

Популярные бренды

Brave VH1724GC, Руководство пользователя

Результаты поиска

Содержание VH1724GC

Отзывы:

Бренды по названию

Популярные бренды