Brave VH1724GC Скачать руководство пользователя

Страница: 13 / 62

Moving and Towing to the Job Site

7. Lock Support

Leg UP

To provide adequate ground clearance while towing, secure the support leg in the UP
position.

8. Tow to Desired

Location

Tow log splitter carefully to desired work site.

(See Step Three: Before Each Use – Work Site Selection and Set-Up)

Important safety instructions



Added length

. Be aware of the added length of the splitter.



Speed limit

. Never tow this log splitter over 45 mph. Faster speeds may

result in loss of control.



Rough terrain

. Drive slowly and take extra caution when traveling over

rough terrain.



On public roads

. If towing on a public road, make sure to comply with all

local, state, and federal towing requirements. It is the sole responsibility of the
purchaser to obtain licensing, trailer lights, safety chains or signage, as needed
to comply.



Unattended

. Turn off the towing vehicle before leaving the splitter

unattended.



Under the influence

. Never tow or operate this splitter while under the

influence of alcohol, drugs, or medication.

9. Lock Support

Leg DOWN and
Unhitch

Lock support leg in the DOWN position and disconnect from vehicle.

NEVER operate log splitter while it is attached to the vehicle.

1.

Lock the support leg down and open the coupler latch assembly.

Unhitch from vehicle.

Lock support leg
in

position

Содержание VH1724GC































































Результаты поиска

Содержание VH1724GC

Отзывы:

Похожие инструкции для VH1724GC

Бренды по названию

Популярные бренды

Brave VH1724GC, Руководство пользователя

Результаты поиска

Содержание VH1724GC

Отзывы:

Похожие инструкции для VH1724GC

Бренды по названию

Популярные бренды