Brave VH1724GC Скачать руководство пользователя | Manualshive

Страница: 1 / 62

background image

1

ITEM NUMBER: __________________

SERIAL NUMBER: ________________

MVH1724A.2

MODELS:

VH1724GC
VH1730GC
VH1737GX

Owner

’

s Manual

Instructions for Assembly, Testing, Operation,

Servicing and Storage

24, 30, & 37 Ton Log Splitters:

Outdoor hydraulic powered machine

that

splits wood logs.

WARNING

READ and UNDERSTAND this manual completely before using log splitter.

All operators of this equipment must read and completely understand all safety information, operating instructions, maintenance
and storage instructions. Failure to properly operate and maintain the log splitter could result in serious injury to the operator and
bystanders from moving parts that can crush or cut, flying objects, burns, fire or explosion, escaping high pressure hydraulic fluid,
or carbon monoxide poisoning in particular, be aware of the following hazards.

Crush and Cut Hazards

Moving parts can crush and cut hands and fingers. Keep hands clear of endplate, wedge, logs, and log dislodger/strippers
while splitting.

High Pressure Hydraulic Fluid Hazards

High fluid pressures and temperatures are developed in hydraulic log splitters. Hydraulic fluid escaping through even a pin-
size hole opening can puncture skin and cause severe blood poisoning. Inspect hydraulic system regularly for possible leaks.
Never check for leaks with your hand while the system is pressurized. Seek medical attention immediately if injured by
escaping fluid.

Fire Hazards



If your log splitter is intended for use near an ignitable forest, brush, or grassy covered land, the engine exhaust should be
equipped with a spark arrestor. See the "Specifications" section of this manual to determine if your splitter already has a spark
arrestor. If not equipped, call Brave Product Support for ordering information.



Keep a class ABC fire extinguisher with you.

STOP

!

ADD OIL TO ENGINE BEFORE USING: Engine

is shipped without oil. DO NOT start log splitter without first adding oil.

ADD HYDRAULIC OIL:

Your log splitter was shipped without hydraulic oil. Refer to Periodic Maintenance section of this manual
for instructions on filling the hydraulic reservoir

PRIME THE PUMP:

The pump on your log splitter needs to be primed before use. Refer to Initial Setup section for instructions.

INSPECT COMPONENTS:

Closely inspect to make sure no components are missing or damaged.

See Initial Unpacking and Set-up for instructions and for whom to contact to report missing or damaged parts.

Any Questions, Comments, Problems or Parts Orders

Call Brave Product Support 1-800-350-8739

1
2
3
...
»

Содержание VH1724GC































































Отзывы:

Нет отзывов

Похожие инструкции для VH1724GC

CUB CADET 24AD598A010

Бренд: MTD Страницы: 3

Бренд: AWD Страницы: 27

1600001-2000000

Бренд: Mountfield Страницы: 44

Бренд: Buffalo Tools Страницы: 23

Бренд: Buffalo Tools Страницы: 31

Бренд: Buffalo Tools Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды