Braun Aquaboss (Eco) RO Dia I HT, Руководство по эксплуатации, Страница: 111 / 132

Technical data Part 2 • Page 7-11
Part 2 – Operating Instructions
Rev. 6.4 dated 2022-02
Software Released Version: 1
(Eco)RO Dia II
Part 2 • Chapt
er 7
Hot RO Condition / Remarks
TISAH1
(4…20mA)
TISAH2
(NTC)
Disinfect
K1106
Dialysis
K1103
Hardness
monitor
K1104
Standby
mode
DO2
Release
HRS
DO21
Alarm*
K1105
Dialysis
lamp
DO1
Standby
lamp
DO2
Flushing
lamp
DO3
Emergency mode
lamp
DO4*
Alarm
lamp
DO5*
0 0 0 0 0 0 0 0 1 0 0 0 0
active not active 0 1 1 0 0 0 1 0 0 0 0 until level below LSHAL1
active not active 0 1 1 0 0 0 1 0 0 0 0 see 6.10.7 Menu 7.1 LSHAL1 or LSHL2 exceeded
active not active 0 1 0 0 0 0 1 0 0 0 0 CD and temp. evaluation delayed 2 min.
Acc. to 6.10.2 to pressure build-up IRS1 line 2.2 or pressure build-up IRS2 line 2.5
active not active 0 1 1 0 0 0 1 0 1 0 0 See 6.10.2 menu 2.6 after operation pressure to flush (line 6)
active not active 0 1 1 0 0 0 1 0 1 0 0 See 6.10.2 menu 2.7 after operation flush back to operation (line 4)
active not active 0 1 1 0 0 0 1 0 1 0 0 See 6.10.2 menu 2.3 after operation pressure to flush (line 8)
active not active 0 1 1 0 0 0 1 0 1 0 0 See 6.10.2 menu 2.4 after operation flush back to operation (line 4)
active not active 0 1 1 0 0 0 1 0 0 0 0 Until WCF ACTUAL = WCF SETPOINT
active not active 0 1 1 0 0 0 1 0 0 0 0 Acc. to 6.10.2 menu 2.16
active not active 0 1 1 0 0 1 1 0 0 1 1 Motor prot. switch 3 failed, conductivity evaluation and temperature evaluation delayed 2 min.
No IRS in emergency mode.
active not active 0 1 1 0 0 1 1 0 0 1 1 Every minute until WCF ACTUAL = WCF SETPOINT
active not active 0 1 1 0 0 1 1 0 0 1 1 Motor protection switch 1 and/or 2 failed. Conductivity and temperature evaluation delayed by
2 min. No IRS in emergency mode.
active not active 0 0 0 1 0 0 0 1 0 0 0 until level falls below LSHAL1. Continue at line 15
active not active 0 0 0 1 0 0 0 1 0 0 0 Fill until LSHAL1 is exceeded. Wait acc. to menu 4.9, when finished, continue at line 16
active not active 0 0 0 1 0 0 0 1 0 0 0 Fill up to LSHL2, then continue at line 17
active not active 0 0 1 1 1 0 0 1 1 0 0 M3 on if 6.10.4 menu 4.5 = 1. Duration according to menu 4.3, then on to line 21.
Y30 on acc. to menu 4.10/4.11/4.12. Leckage monitoring on, conductivity monitoring OFF.
active not active 0 0 1 1 1 0 0 1 1 0 0 Only with EcoRO Dia and menu 4.6 = On. Pressure build-up according to menu 2.6.
When finished, continue at line 19
active not active 0 0 1 1 1 0 0 1 1 0 0 Only with EcoRO Dia and menu 4.6 = On. Flush according to menu 2.7.
When finished, continue at line 17.
active not active 0 0 1 1 1 0 0 1 0 0 0 Start when menu 4.4 = on and start value XX°C reached.
Stop temp. discharge when stop value XX°C reached.
When DI 06 = 0 cancel intermediate flush and change to break. When Y9 = 1 and
LSHL2 > 5 sec = 0, close Y9 unitl LSHL2 = 1 and then open Y9 again
active not active 0 0 0 1 1 0 0 1 0 0 0 Time-controlled: acc. to menu 4.2 + 4.3
active not active 0 0 1 1 1 0 0 1 0 0 0 Menu 4.2 + 4.3 = 0 minutes. Leak monitoring
active not active 1 0 0 0 0 1 0 0 0 0 1 until level below LSHAL1, then line 24
active not active 1 0 0 0 0 1 0 0 0 0 1 Continue using keyboard
active not active 0 until LSHL2 exceeded
active not active 1 0 0 0 0 1 0 0 0 0 1 Permeate conductivity control, display time left. If conductivity > 98μS/cm after 20 min, continue
at line 31. Duration acc. to chap. 6.10.5 menu 5.2; then line 31
active not active 1 0 0 0 0 1 0 0 1 0 1 During recirculation mode +1 min, continue at line 28
active not active 1 0 0 0 0 1 0 0 1 0 1 After comp 30 sec: continue at line 29
active not active 1 0 0 0 0 1 0 0 1 0 1 Then line 30
active not active 1 0 0 0 0 1 0 0 1 0 1 Then back to line 26
active not active 1 0 0 0 0 1 0 0 0 0 1 Display of time left. Duration: 6.10.5: menu 5.3. Then continue at line 32
active not active 1 0 0 0 0 1 0 0 0 0 1 until LSHL2 exceeded
active not active 1 0 0 0 0 1 0 0 0 0 1 If level below LSHAL1, back to filling tank
Message from 15 minutes before the end: Check disinfectant residue. If conductivity > +25%
after disinfection, back to start of line 32. Keyboard back to rinsing mode or end of disinfection.
End = back to basic state of standby mode or off. If LSHL2 exceeded, IRS1 or IRS2 alternately.
active not active 1 0 0 0 0 1 0 0 1 0 1 After completion of menu 2.7 continue with emptying tank line 33
active not active 1 0 0 0 0 1 0 0 1 0 1 After completion of menu 2.4 continue with emptying tank line 33
active not active 1 0 0 0 0 1 0 0 0 0 1 until level below LSHAL1, then line 37
active not active 1 0 0 0 0 1 0 0 0 0 1 Continue using keyboard
active not active 0 0 until LSHL2 exceeded
active not active 1 0 0 0 0 1 0 0 0 0 1 Display of time left. Duration according to chap. 6.10.6 menu 6.2; then line 41
active not active 1 0 0 0 0 1 0 0 1 0 1 During recirculation mode +1 min, continue at line 41
active not active 1 0 0 0 0 1 0 0 1 0 1 After comp 30 sec: continue at line 42
active not active 1 0 0 0 0 1 0 0 1 0 1 Then line 43
active not active 1 0 0 0 0 1 0 0 1 0 1 Then back to line 39
active not active 1 0 0 0 0 1 0 0 0 0 1 Display of time left. Duration: 6.10.6 menu 6.3. Then continue at line 45
active not active 1 0 0 0 0 1 0 0 0 0 1 until LSHL2 exceeded
active not active 1 0 0 0 0 1 0 0 0 0 1 If level below LSHAL1, back to filling tank
Message from 15 minutes before the end: Check cleaning solution residue. Keyboard back to
rinsing mode or end of cleaning. End = back to basic state of standby mode or off. If LSHL2
exceeded, IRS1 or IRS2 alternately.
active not active 1 0 0 0 0 1 0 0 1 0 1 After completion of menu 2.7 continue with emptying tank line 46
active not active 1 0 0 0 0 1 0 0 1 0 1 After completion of menu 2.4 continue with emptying tank line 46
not active active 1 0 0 1 1 0 0 1 0 0 0 • Heat up until temp. menu 12.2 reached
• #3 = Close Y90 when
ǻ
T
•
2°K/min., open when
ǻ
T
”
+2°K/min.
not active active 1 0 0 1 1 0 0 1 0 0 0 • #3 = Close Y90 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• Duration according to menu 12.4 or menu 12.5
• After end of period change to cooling phase
not active active 1 0 0 1 1 0 0 1 0 0 0 • #14 = Close Y8 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #15 = Actual temperature menu 12.2 reached, close Y5, Y5.1 and Y8
• Actual temperature menu 12.2 reached, back to line 21 "Standby mode break"
not active active 1 0 0 1 1 0 0 1 0 0 0 • #14 = Close Y8 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #15 = Actual temperature menu 12.2 reached, close Y5, Y5.1 and Y8
not active active #10 1 1 0 0 0 1 0 0 0 0 • #10 = As long as signal HWD1 is pending, Y5.1.1 off and K1106 disinfection on, when signal
HWD1 is no longer pending, Y5.1.1 off and K1106 disinfection off.
• #14 = Close Y8 when
ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #15 = Actual temperature menu 12.2 reached, close Y5, Y5.1 and Y8.
active active 1 0 0 1 1 0 0 1 0 0 0 • Heating until temp. menu 12.3 or 12.12 is reached
• #2 = Close Y5.1.1 when
ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #4 = Open Y30 every 120 seconds for 1 sec, when Y30 closed again, open Y3 for 2 sec, when
Y3 closed again, open Y6 for 2 sec, when Y6 closed again, open Y7 for 2 sec and switch M3 on
at the same time, when Y7 open close Y8
active active 1 0 0 1 1 0 0 1 0 0 0 • #2 = Close Y5.1.1 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #4 = Open Y30 every 120 seconds for 1 sec, when Y30 closed again, open Y3 for 2 sec, when
Y3 closed again, open Y6 for 2 sec, when Y6 closed again, open Y7 for 2 sec and switch M3 on
at the same time, when Y7 open close Y8
active active 1 0 0 1 1 0 0 1 0 0 0 • #14 = Close Y8 when
ǻ
T
•
2°K/min., open when
ǻ
T
”
+2°K/min.
• #11 = Close Y9 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• Actual temperature menu 12.3 or 12.12 reached, back to line 21 "Standby mode break"
active active 1 0 0 1 1 0 0 1 0 0 0 • #14 = Close Y8 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #11 = Close Y9 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
active active #10 1 1 0 0 0 1 0 0 0 0 • #10 = As long as signal HWD1 is pending, Y5.1.1 off and K1106 disinfection on, when signal
HWD1 is no longer pending, Y5.1.1 off and K1106 disinfection off.
• #11 = Close Y9 when
ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #14 = Close Y8 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
active active 1 0 0 1 1 0 0 1 0 0 0 • Heating until temp. menu 12.20 is reached
• #2 = Close Y5.1.1 when
ǻ
T
•
2°K/min., open when
ǻ
T
”
+2°K/min.
• #16 = Open Y30 every 120 seconds for 1 sec, when Y30 closed again, open Y3 for 2 sec,
when Y3 closed again, open Y6 for 2 sec.
active active 1 0 0 1 1 0 0 1 0 0 0 • #2 = Close Y5.1.1 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• #16 = Open Y30 every 120 seconds for 1 sec, when Y30 closed again, open Y3 for 2 sec,
when Y3 closed again, open Y6 for 2 sec.
active active 1 0 0 1 1 0 0 1 0 0 0 • #11 = Close Y9 when ǻ T • 2°K/min., open when ǻ T ” +2°K/min.
• Actual temperature menu 12.4 reached, back to line 21 "Standby mode break"
active active 1 0 0 1 1 0 0 1 0 0 0 • #11 = Close Y9 if ǻ T • 2°K/min., open if ǻ T ” +2°K/min.
active active #10 1 1 0 0 0 1 0 0 0 0 • #10 = As long as signal HWD1 is pending, Y5.1.1 off and K1106 disinfection on, when signal
HWD1 is no longer pending, Y5.1.1 off and K1106 disinfection off.