Brandt GRAIN VAC 5000 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 104

Brandt GRAIN VAC 5000 Скачать руководство пользователя страница 34

33

Section 4 - Service

4.1 Fluids and Lubricants

1. Grease - Use an SAE multipurpose high

temperature grease with extreme-pressure (EP)
rating. Also acceptable is an SAE multipurpose
lithium based grease. Use multipurpose SD
Polyurea grease on the PTO shaft.

2. Gearbox Oil - Use SAE 80W90 gear oil in the

gearbox for all working conditions.

3. Fan Bearing Box Oil - Use 75W90 Synthetic

gear oil for all working conditions.

4. Storing Lubricants - Your machine can operate

at top efficiency only if clean lubricants are used.
Use clean containers to handle all lubricants.
Store them in an area protected from dust,
moisture and other contaminants.

4.2 Lubrication

1. Use the Maintenance Checklist provided to

keep a record of all scheduled maintenance.

2. Use a hand held grease gun for all greasing.

3. Wipe fittings clean before greasing to avoid

injecting dirt and grit.

4. Repair and replace broken or missing fittings

immediately.

5. If fittings will not take grease, remove and clean

thoroughly. Also clean lubricant passageway.
Replace fitting if necessary.

F

IG

. 16 L

UBRICATION

S

CHEDULE

Use Multi-purpose SD Polyurea Grease on the PTO Shaft

«
...
32
33
34
35
36
...
»

Содержание GRAIN VAC 5000









































































































Отзывы:

Нет отзывов