Bradley Terreon Tri-Fount MF2933/IR Скачать руководство пользователя | Manualshive

Страница: 8 / 68

background image

MF2933/IR

Installation

8

10-28-2005

Bradley Corporation • 215-1176 Rev. R; EN 06-915C

Braided Hose

Cold Supply Inlet

Hot Supply
Inlet

Stop/Check Valve

Vernatherm™ TMV

Solenoid Valve Assembly

1/4-20 x 1/2" Screws

Figure 3

4

Install solenoid assembly

CONNECT THE 1/2" NPT FEMALE END OF THE STOP/CHECK
VALVES TO THE ROUGH-INS.

A

CONNECT THE SUPPLY HOSES TO THE STOP/CHECK VALVES.

B

NOTE!

The letter “H” on the Vernatherm™
Mixing Valve indicates hot water supply
inlet.

The thermostatic mixing valve requires
at least 115° F water from the hot water
side for proper operation. As with all
lavatories, there will be a delay in
obtaining warm water. If the hot water is
too far away from the washfountain, a
circulating pump may be required.

INSIDE THE PEDESTAL, INSTALL THE TWO 1/4-20 X 1/2" SCREWS (SUPPLIED WITH VALVE ASSEMBLY) IN THE
MOUNTING HOLES ON THE SIDE OF THE LEFT PEDESTAL PANEL. DO NOT THREAD THE SCREW COMPLETELY
INTO THE PANEL, BUT ALLOW 5/16" OF THE SCREW TO BE EXPOSED (SEE FIGURE 3)

C

MOUNT THE VALVE BRACKET TO THE LEFT SIDE OF THE PEDESTAL AS SHOWN.

D

CONNECT THE SUPPLY HOSES TO THE VERNATHERM™ TMV VALVE ASSEMBLY.

E

FOR OPTIONAL SINGLE TEMPERED SUPPLY: ATTACH THE STOP/CHECK VALVE TO THE 1/2" TEMPERED SUPPLY LINE.
CONNECT THE STOP/CHECK VALVE TO THE SOLENOID VALVE ASSEMBLY WITH THE FLEXIBLE SUPPLY HOSE.

F

«
...
6
7
8
9
10
...
»

Содержание Terreon Tri-Fount MF2933/IR





































































Отзывы:

Нет отзывов

Похожие инструкции для Terreon Tri-Fount MF2933/IR

Ceylon Loveseat SO625

Бренд: Ballard Designs Страницы: 5

Бренд: Garden Gear Страницы: 2

Бренд: Sport-thieme Страницы: 3

Бренд: Joyside Страницы: 31

Cara Classic FT-47

Бренд: Campania International Страницы: 4

Бренд: V-TAC Страницы: 13

Expert HUB1600RWBCEE

Бренд: XanLite Страницы: 7

Бренд: Dale Tiffany Страницы: 3

Wainwright RCPWT63

Бренд: Anova Страницы: 6

SEC17 RW U8 W/MTL KD

Бренд: Veranda Страницы: 13

Бренд: Glendale Страницы: 5

Бренд: oldfields Treco Страницы: 28

Palermo Garden Gazebo 4300

Бренд: Palram Страницы: 16

Бренд: PATIOJOY Страницы: 5

SmartStore SM2520

Бренд: Riverlea Страницы: 16

Бренд: WE-EF Страницы: 7

LE PERROQUET MXZ2

Бренд: iGuzzini Страницы: 23

Бренд: XanLite Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды