Bradley Terreon Tri-Fount MF2933/IR Скачать руководство пользователя | Manualshive

Страница: 12 / 68

background image

MF2933/IR

Installation

12

10-28-2005

Bradley Corporation • 215-1176 Rev. R; EN 06-915C

Cleaning and maintenance instructions for Terreon

®

Material Description:

Terreon

®

is a NAHB Certified densified solid surface material composed of polyester

resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with
everyday cleansers or fine grit abrasives.

Routine Cleaning:

Clean daily or as often as conditions require using a standard commercial or household

cleaner such as Formula 409

®

or Windex

®

.

Stubborn Stains:

Remove tough stains with Ajax

®

, Comet

®

, or Soft-Scrub

®

and a green Scotch-Brite

®

pad or

lightly sand in a circular motion with 240 grit wet/dry sandpaper. The finish can be renewed with a maroon
Scotch-Brite pad.

Special Situations for Material

Scratches:

Remove scratches with a green Scotch-Brite

®

pad. The finish can then be renewed with a maroon

Scotch-Brite

®

pad.

Hard Water Deposits:

Remove hard water deposits with a mild solution of vinegar and water. Always rinse

the unit thoroughly after cleaning.

Restoring the surface:

Use Hope's

®

Solid Surface cleaner and polish to refresh and protect the Terreon

Solid Surface material.Bradley recommends additional care and maintenance for the darker colored Terreon,
for complete instructions on this additional maintenance see Bradley document #1505.

IMPORTANT:

DO NOT USE STRONG ACID OR ALKALINE CHEMICALS AND
CLEANSERS TO CLEAN TERREON. IF THESE CHEMICALS COME IN
CONTACT WITH THE TERREON SURFACE, WIPE THEM OFF
IMMEDIATELY AND RINSE WITH SOAPY WATER.

AVOID CONTACT WITH HARSH CHEMICALS SUCH AS PAINT REMOVER,
BLEACH, ACETONE, ETC. AVOID CONTACT WITH HOT PANS AND
OBJECTS.

Repair Kits:

Terreon

®

repair kits are available. Contact your Bradley representative or distributor for part

numbers and pricing.

NOTE: Repair kits are made to order and have a shelf life of 30 days.

Brand Names:

Use of brand names is intended only to indicate a type of cleaner. This does not constitute an

endorsement, or does the omission of any brand name cleaner imply it’s inadequacy. Many products named are
regional in distribution, and can be found in local supermarkets, department and hardware stores, or through
your cleaning service. It is emphasized that all products should be used in strict accordance with package
instructions.

NOTE: When cleaning units equipped with infrared (electronic eye) activation, it is helpful to turn off
the power to the unit or cover the windows to prevent accidental activation. After the window is
covered, the water will run for approximately 30 seconds and then shut off.

«
...
10
11
12
13
14
...
»

Содержание Terreon Tri-Fount MF2933/IR





































































Отзывы:

Нет отзывов

Похожие инструкции для Terreon Tri-Fount MF2933/IR

Бренд: Gazelle Страницы: 6

Emily Coffee Table

Бренд: Zest 4 Leisure Страницы: 3

Бренд: Gama Sonic Страницы: 4

Solar-LED-Motion-Curve

Бренд: Zled Lighting Страницы: 2

Бренд: Campania International Страницы: 2

Бренд: Palram Страницы: 33

Бренд: V-TAC Страницы: 31

Бренд: Oase Страницы: 100

Бренд: leadsun Страницы: 9

DUOTECH HIGH-STORE+ 1403609

Бренд: Keter Страницы: 36

Бренд: CobraCo Страницы: 4

Бренд: HAMPTON BAY Страницы: 8

Бренд: Sunjoy Страницы: 14

Бренд: Sontax Страницы: 5

Impressionist Series

Бренд: CAST Lighting Страницы: 2

Бренд: EAST OAK Страницы: 7

Бренд: Ballard Designs Страницы: 3

Бренд: STERNO HOME Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды