manualshive.com logo in svg

Bradley Terreon Tri-Fount MF2933/IR, Руководство по установке

Поделиться
Скачать
Bradley Terreon Tri-Fount MF2933/IR Скачать руководство пользователя страница 55

Bradley Corporation • 215-1537 Rev. D; 06-915C

Terreon® Tri-Fount™ Washfountain with Touch Time® Control

Installation Instructions

MF2933/TT

3

2-28-2005

Parts Included with the Tri-Fount™

Separate all parts from packaging materials and ensure you have all the parts required for assembly.
If any parts are missing, do not attempt to assemble the Bradley Terreon

®

Tri-Fount™ Washfountain

until you obtain all parts.

MOUNTING PANELS

LOWER BRACKET 

VALVE PREPACK S45-2082 

Stop/Check

Hose

TEMPERED LINE

S45-2081 (OPTIONAL) 

Stop/Check

Hose

Solenoid Assembly with

Two Mounting Screws

Supplies required:

• (6) 3/8" diameter bolts with washers and (6) wall anchors appropriate for your installation
• (2) 3/8" diameter bolts with washers and (2) floor anchors appropriate for your installation
• 1/2" NPT Hot and cold water supply lines
• 1-1/2" NPT drain trap and waste connection
• Pipe sealant and plumber’s putty
• 110 VAC power source for 110/24 VAC plug-in transformer supplied
• OPTIONAL: Bradley recommends installing an electrical cut-off switch to the unit. This

feature prevents accidental water delivery during regular maintenance and service.

Содержание Terreon Tri-Fount MF2933/IR





































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды