Bradley Terreon Tri-Fount MF2933/IR Скачать руководство пользователя | Manualshive

Страница: 59 / 68

background image

Bradley Corporation • 215-1537 Rev. D; 06-915C

Terreon® Tri-Fount™ Washfountain with Touch Time® Control

Installation Instructions

MF2933/TT

7

2-28-2005

Installation Instructions continued . . .

Step 5: Install solenoid assembly

1. Connect the 1/2" NPT female end of the stop/check valves to the rough-ins.

2. Connect the supply hoses to the stop/check valves.

3. Inside the pedestal, install the two 1/4-20 x 1/2" screws (supplied with solenoid assembly) in the

mounting holes on the side of the left pedestal panel.

DO NOT

thread the screw completely

into the panel, but allow 5/16" of the screw to be exposed (see Figure 4)

4. Mount the valve bracket to the left side of the pedestal as shown.

IMPORTANT: The hose attached to the hot water inlet of the Vernatherm™ TMV

valve (marked with “H”) must be connected to the hot water rough-in.

5. Connect the supply hoses to the Vernatherm™ TMV valve assembly.

6. FOR OPTIONAL SINGLE TEMPERED SUPPLY: Attach the stop/check/valve to the 1/2" tempered

supply line. Connect the stop/check/valve to the solenoid valve with the flexible supply hose.

NOTE: The thermostatic mixing valve requires at least 115° F water from the hot water side for
proper operation. As with all lavatories, there will be a delay in obtaining warm water. If the hot
water is too far away from the washfountain, a circulating pump may be required.

Braided Hose

Cold Supply Inlet

Hot Supply
Inlet

Stop/Check Valve

Vernatherm™ TMV

Solenoid Valve Assembly

1/4-20 x 1/2" Screws

Figure 4

«
...
57
58
59
60
61
...
»

Содержание Terreon Tri-Fount MF2933/IR





































































Отзывы:

Нет отзывов

Похожие инструкции для Terreon Tri-Fount MF2933/IR

Бренд: Waldbeck Страницы: 24

Бренд: Quoizel Страницы: 2

Бренд: Paloform Страницы: 16

Бренд: Dancover Страницы: 30

JHOOLA DAY BED SWING SETS

Бренд: Forever Redwood Страницы: 12

Бренд: Campania International Страницы: 4

Бренд: KAWOTI Страницы: 4

Бренд: Hanover Страницы: 4

Бренд: Daifuku Страницы: 24

Бренд: Mimosa Страницы: 20

Бренд: Tricam Страницы: 2

HERAKLION 149045

Бренд: Hesperide Страницы: 28

Бренд: Backyard Discovery Страницы: 22

Бренд: Gardiun Страницы: 26

Бренд: arte confort Страницы: 7

Photographic 807726

Бренд: Habitat Страницы: 3

Бренд: Deuba Страницы: 6

LAVDN7PCSW-SLV-SU

Бренд: Hanover Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды