Bosch VIP XD Скачать руководство пользователя страница 63

Страница: 63 / 80

VIP XD

Appendix | en

Bosch Security Systems

Installation and Operating Manual

DOC | V4.0 | 2009.06

Appendix

8.1

Troubleshooting

If you are unable to resolve a malfunction, please contact your supplier or systems integrator,

or go directly to Bosch Security Systems Customer Service.

You can view a range of information about your unit version on the

System Overview

page

(see

Section 5.23 System Overview, page 51

). Make a note of this information before

contacting Customer Service. You can download an internal maintenance log from the unit on

the

Maintenance

page if you wish to send it to Customer Service by e-mail (see

Section Maintenance log, page 50

The following table is intended to help you identify the causes of malfunctions and correct

them where possible.

Malfunction

Possible causes

Recommended solution

No connection between

the unit and terminal

program.

Incorrect cable connections.

Check all cables, plugs,

contacts, terminals and

connections.

The computer's serial interface

is not connected.

Check the other serial interface.

Interface parameters do not

match.

If necessary select a different

interface and make sure that the

computer's interface parameters

match those of the unit. Try the

following standard parameters:

19,200 baud, 8 data bits, no

parity, 1 stop bit. Next,

disconnect the unit from the

power supply and reconnect it

again after a few seconds.

No image on the monitor. Monitor error.

Connect local camera or other

video source to the monitor and

check the monitor function.

Faulty cable connections.

Check all cables, plugs, contacts

and connections.

No connection

established, no image

transmission.

The unit's configuration.

Check all configuration

parameters.

Faulty installation.

Check all cables, plugs, contacts

and connections.

Wrong IP address.

Check the IP addresses

(terminal program).

Faulty data transmission within

the LAN.

Check the data transmission

with

ping

The maximum number of

connections has been reached.

Wait until there is a free

connection and then call the

sender again.

Содержание VIP XD

















































































Результаты поиска

Содержание VIP XD

Отзывы:

Похожие инструкции для VIP XD

Бренды по названию

Популярные бренды

Bosch VIP XD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VIP XD

Отзывы:

Похожие инструкции для VIP XD

Бренды по названию

Популярные бренды