Bosch VIP XD Скачать руководство пользователя страница 34

Страница: 34 / 80

en | Configuration Using a Web Browser

VIP XD

DOC | V4.0 | 2009.06

Installation and Operating Manual

Bosch Security Systems

Line In / Microphone (MIC)

You can set the audio signal gain for the line and microphone input. Make sure that the display

does not go beyond the green zone during modulation.

Line Out/Speaker (SPK)

You can set the gain of the line and loudspeaker output. Make sure that the display does not

go beyond the green zone during modulation.

Selection

Click one of the option boxes and then click

Set

to display the level of the respective audio

input for orientation and to set the gain.

5.11

Alarm Connections

You can select how the VIP XD responds to an alarm. In the event of an alarm, the unit can

automatically connect to a pre-defined IP address. You can enter up to ten IP addresses to

which the VIP XD will connect in sequence in the event of an alarm, until a connection is

made.

Connect on alarm

Select

so that the VIP XD automatically connects to a predefined IP address in the event of

an alarm.

By setting

Follows input 1

, the VIP XD automatically connects to a remote station and holds

the connection as long as an alarm exists on alarm input 1. This option can also be used to

connect two units (sender and receiver) via a switch connected to the VIP XD. You do not

need a computer to make the connection in this case.

NOTICE!

In the default setting, Stream 2 is transmitted for automatic connections. Bear this fact in

mind when assigning the profile to the corresponding sender.

Содержание VIP XD

















































































Результаты поиска

Содержание VIP XD

Отзывы:

Похожие инструкции для VIP XD

Бренды по названию

Популярные бренды

Bosch VIP XD, Инструкция по установке и эксплуатации

Результаты поиска

Содержание VIP XD

Отзывы:

Похожие инструкции для VIP XD

Бренды по названию

Популярные бренды