Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя | Manualshive

Страница: 12 / 53

background image

Safety instructions 11/52

Bosch Rexroth Mellansel AB

, Installation and maintenance manual, Hägglunds CA 10 - CA 40, RE 15354-WA/04.2015

wARNING

Escaping oil mist!

Risk of explosion, fire, health hazard, environmental pollution!

▶

Depressurize the machine/system and repair the leak.

▶

Keep open flames and ignition sources away from the Hägglunds motors.

▶

If Hägglunds motors are to be situated in the vicinity of ignition sources or
powerful thermal radiators, a shield must be erected to ensure that any escaped

hydraulic fluid can not ignite, and to protect hose lines from premature aging.

CAUTION

High noise development in operation!

Danger of hearing damage, deafness!
The noise emission of Hägglunds motors depends on speed, operating pressure and
installation conditions.

▶

Always wear hearing protection when in the vicinity of the operating radial
piston motor.

Hot surfaces on the radial piston motor!

Risk of burns!

▶

Allow the Hägglunds motors to cool down sufficiently before touching it.

▶

Wear heat-resistant protective clothing, e.g. gloves.

Improper routing of cables and lines!

Tripping hazard and damage to equipment!

▶

Lay cables and lines so that they can not be damaged and nobody can trip over
them.

Contact with hydraulic fluid!

Hazard to health/health impairment e.g. eye injuries, skin damage, toxication during
inhalation!

▶

Avoid contact with hydraulic fluids.

▶

When working with hydraulic fluids, strictly observe the safety instructions

provided by the lubricant manufacturer.

▶

Use your personal protective equipment (e.g. safety glasses, safety gloves,
suitable working clothes, safety shoes).

▶

If hydraulic fluid should, nevertheless, come into contact with your eyes or

bloodstream or is swallowed, consult a doctor immediately.

Escaping hydraulic fluid due to machine/system leakage!

Risk of burns and risk of injury due to escaping oil jet!

▶

Depressurize the machine/system and repair the leak.

▶

Never attempt to block or seal the leak or oil jet with a cloth.

2.7 Personal protection equipment

The personal protective equipment is the responsibility of the user of the Hägglunds
motors. Observe the safety regulations and provisions of your country. All
components of the personal protective equipment must be intact.

«
...
10
11
12
13
14
...
»

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth Hagglunds CA 10

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: HunterDouglas Страницы: 20

Бренд: FeiaoModel Страницы: 7

Бренд: Saito Страницы: 8

Бренд: Sole Diesel Страницы: 40

Бренд: Yaroslavl Engine Plant Страницы: 168

Бренд: Wisconsin Motors Страницы: 46

Бренд: Mile HaoXianG Model Technology Страницы: 3

Бренд: Leroy-Somer Страницы: 8

Бренд: Leroy-Somer Страницы: 6

MICRO GEARLESS XAP1-CE

Бренд: Leroy-Somer Страницы: 12

Бренд: EX Model Engines Страницы: 2

Бренд: Nederman Страницы: 44

Бренд: Louvolite Страницы: 2

Бренд: CAME Страницы: 96

ZA top SM225.40B

Бренд: ZIEHL-ABEGG Страницы: 76

Бренд: WilTec Страницы: 6

Бренд: WilTec Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды