manualshive.com logo in svg

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Поделиться
Скачать
Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 41

40/52

 Troubleshooting

RE 15354-WA/04.2015, Installation and maintenance manual, Hägglunds CA 10 - CA 40, 

Bosch Rexroth Mellansel AB

Table 17: Troubleshooting hydraulic motor

Fault

Probable cause

Action

The motor does not run.

Mechanical stop in the drive.

Check system pressure. If the pressure has 
risen to the relief valve setting, remove the load 
from the drive.

The motor does not deliver enough torque 

because the pressure difference across the 

motor is not enough for the load.

Investigate the pressure level in the system and 
correct the setting of the pressure limiting valve 
if necessary.

Insufficient or no oil being supplied to motor.

Check the hydraulic system. Check the external 
leakage of the motor (D connection).

Motor rotates in wrong direction.

Oil supply connections to motor incorrectly 
connected.

Connect the oil supply correctly.

Motor runs jerkily.

Pressure or flow fluctuations in the hydraulic 

system.

Find the cause in the system or in the driven 
unit.

Noise in the motor.

The motor is being operated with too low 
charge pressure.

Adjust the charge pressure to the correct level. 
See chapter 

15.1.2: Recommended charge 

pressure

 

Internal faults in the motor.

Investigate the drain oil, if necessary. Put 

a magnetic plug in the oil flow and check 

the material that sticks to the magnet. Steel 

particles indicate damage. Note that fine 

material from the castings may be deposited 
and does not mean internal damage in the 
motor.

External oil leakage on the motor.

The radial lip seal is worn.

Replace the radial lip seal.

14  Troubleshooting

Please, contact your nearest Bosch Rexroth representative.

Содержание Rexroth Hagglunds CA 10






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды