Bosch Rexroth Hagglunds CA 10 Скачать руководство пользователя страница 25

Страница: 25 / 53

24/52 Installation

RE 15354-WA/04.2015, Installation and maintenance manual, Hägglunds CA 10 - CA 40,

Bosch Rexroth Mellansel AB

7.3.2 lubrication of spline

For flange mounted motors, the spline shall normally not be subject to radial load.

With no radial load, the spline shaft can be oiled before mounting the motor. If the

motor is subject to radial load, the splines shall be filled up with oil.

See

Table 10: Oil

volume for lubrication of spline connection

1. Lubricate and install O-ring at leading edge of motor bore. (O-ring is included in

delivery)

2. Check shaft/splines for burrs and lubricate shaft/splines.
3. Mark spline tooth location on outside of motor bore to assist alignment during

installation.

4. Mount the motor on to the shaft. For screw dimensions and tightening torque,

see

Table 8: Dimensions installation tolerances CA 10 CA 20 and Table 9: Dimensions

installation tolerances CA 30 CA 40

Bolt the motor to the flange.

6. Fill up hydraulic oil to the G3/8 tread. (see

Fig. 11: Flange mounted motor, shaft

horizontal)

Torque the G3/8 plug. Torque = 30 Nm (22 lbf·ft).

Mount the cover. Torque = 10 Nm (7 lbf·ft).

Table 10: Oil volume for lubrication of spline connection

Motor type

litre

US gallon

CA 10

0.12

0.032

CA 20

0.20

0.053

CA 30

0.48

0.127

CA 40

0.70

0.185

Fig. 11: Flange mounted motor, shaft horizontal

If oil here, it can be used
for the spline. Then take
away the o-ring.

O-ring

74.5 x 3.0 mm
(2.93 x 0.12 in)

Oil to be filled before

tightening G 3/8 plug.

Plug G3/8

DD00063756

Cover

Содержание Rexroth Hagglunds CA 10






















































Результаты поиска

Содержание Rexroth Hagglunds CA 10

Отзывы:

Бренды по названию

Популярные бренды

Bosch Rexroth Hagglunds CA 10, Руководство по установке и обслуживанию

Результаты поиска

Содержание Rexroth Hagglunds CA 10

Отзывы:

Бренды по названию

Популярные бренды