Bosch Rexroth 3 Series Скачать руководство пользователя | Manualshive

Страница: 35 / 68

background image

Installation 35/68

RE 92105-01-B/06.2017, A4CSG, Series 3x,

Bosch Rexroth AG

7.4.6 Installation with cardan shaft

To connect the axial piston unit to the drive motor via a cardan shaft.

nOTICE!

Damage to the axial piston unit and leaks at the shaft seal!

Improperly installed cardan shafts generate unbalances. This results in vibrations
and impermissible forces on the drive shaft.
Observe the cardan shaft manufacturer's assembly instructions.

1.

Position the axial piston unit close to the specified installation location. Allow
enough space for the cardan shaft to fit through on both sides.

2.

Position the cardan shaft on the output shaft of the drive motor.

3.

Push the axial piston unit to the cardan shaft and position the cardan shaft on the
drive shaft of the axial piston unit.

4.

Bring the axial piston unit to the installation position and secure. If necessary,
details on the required tools and tightening torques for the mounting bolts can be
obtained from the system manufacturer.

7.4.7 Completing installation

1.

Remove any mounted transport screws.

CAUTIOn!

Operation with protective plugs!

Operating the axial piston unit with protective plugs may result in injuries or damage
to the axial piston unit.

▶

Before commissioning, remove all protective plugs and replace them with
suitable, pressure-resistant, metal threaded plugs or connect the appropriate
lines.

2.

Remove the transport protection.
The axial piston unit is delivered with protective covers (

1

) and protective plugs (

2

).

They are not pressure-resistant and have to be removed prior to connection. Use
a suitable tool for this to prevent damage to the sealing and functional surfaces.
If sealing or functional surfaces are damaged, contact your Bosch Rexroth service
partner or the service department of the manufacturer's plant for the axial
piston unit.

«
...
33
34
35
36
37
...
»

Содержание Rexroth 3 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth 3 Series

Бренд: Waterous Страницы: 13

Бренд: Waterous Страницы: 57

Бренд: SereneLife Страницы: 10

Бренд: Mueller Страницы: 46

Бренд: Wilo Страницы: 76

Бренд: Zoeller Страницы: 16

Бренд: STIEBEL ELTRON Страницы: 15

BREDEL 701 Series

Бренд: Watson-Marlow Страницы: 25

Бренд: Xylem Страницы: 56

Бренд: Grundfos Страницы: 16

1542A-SP Series

Бренд: Hypro Страницы: 8

Бренд: All-Flo Страницы: 28

Бренд: Campbell Hausfeld Страницы: 4

Бренд: Quality Страницы: 11

Бренд: Nilfisk-Advance Страницы: 84

Бренд: Eckerle Страницы: 16

NCE H 25-100/180

Бренд: Calpeda Страницы: 72

OKCE 100 NTR/2,2kW

Бренд: Dražice Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды