Bosch Rexroth 3 Series Скачать руководство пользователя | Manualshive

Страница: 13 / 68

background image

Safety instructions 13/68

RE 92105-01-B/06.2017, A4CSG, Series 3x,

Bosch Rexroth AG

CAUTIOn

High noise development during operation!

Risk of hearing damage or hearing loss!
The noise emission of axial piston units depends on, among other factors,
rotational speed, working pressure and installation conditions. The sound pressure
level may rise above 70 dB (A) during normal application conditions.

▶

Always wear hearing protection when in the vicinity of the operating axial piston
unit.

Hot surfaces on the axial piston unit!

Risk of burning!

▶

Allow the axial piston unit to cool down sufficiently before touching it.

▶

Wear heat-resistant protective clothing, for example, gloves.

Improper routing of cables and lines!

Risk of stumbling and property damage! Improper routing of cables and lines can
cause a risk of stumbling as well as damage to equipment and components, for
example, tearing of lines and connectors.

▶

Always lay cables and lines in such a way that no one can trip over them, that
they do not become kinked or twisted, do not rub on edges and do not run
without adequate protection through sharp-edged ducts.

Contact with hydraulic fluid!

Risk of adverse health effects, e.g. eye injury, skin irritation, poisoning from
inhalation!

▶

Avoid contact with hydraulic fluids.

▶

When working with hydraulic fluids, strictly observe the safety instructions
provided by the lubricant manufacturer.

▶

Wear your personal protective equipment (e.g. safety goggles, safety gloves,
suitable working clothes, safety shoes).

▶

Consult a doctor immediately if hydraulic fluid gets in your eyes or bloodstream,
or is swallowed.

Escaping hydraulic fluid due to machine/system leakage!

Risk of burns and risk of injury due to escaping oil jet!

▶

Depressurize the relevant machine/system part and repair the leak.

▶

Never attempt to block or seal the leak or oil jet with a cloth.

Danger from improper handling!

Risk of slipping! Risk of slipping on wet surfaces when climbing on the axial piston
unit.

▶

Never grab or climb onto the axial piston unit.

▶

Check how to safely get on top of the machine/system.

«
...
11
12
13
14
15
...
»

Содержание Rexroth 3 Series





































































Отзывы:

Нет отзывов

Похожие инструкции для Rexroth 3 Series

Бренд: EarthLinked Страницы: 6

Бренд: CIAT Страницы: 35

Бренд: Ulvac Страницы: 54

Altherma EKHWE150A3V3

Бренд: Daikin Страницы: 10

Бренд: EBARA Страницы: 48

Бренд: CTC Union Страницы: 2

Бренд: STAR Water Systems Страницы: 8

RediHeat RH-120

Бренд: Spirax Sarco Страницы: 12

Бренд: Varian Страницы: 24

Бренд: Launtop Страницы: 22

Бренд: XtremepowerUS Страницы: 14

Бренд: CME Страницы: 28

Бренд: Carrier Страницы: 28

Бренд: FLYGT Страницы: 172

Бренд: Heatcraft Refrigeration Products Страницы: 20

Water Heater 520 Direct Vent Indoor

Бренд: A.O. Smith Страницы: 97

Бренд: Williamson Страницы: 8

Бренд: Zenit Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды