Bosch Performance Line CX, Системное руководство

Страница: 89 / 296

English– 3
0 275 U07 PDC | (9.5.17) Bosch eBike Systems
Operating your Bosch Drive Unit
Safety Rules
Read and understand all safety warnings and
instructions. Failure to follow the warnings be-
low could result in death or serious injury.
Save all safety warnings and instructions for future
reference.
The term “battery pack” used in these operating instruc-
tions refers to all original Bosch eBike battery packs.

Do not open the drive unit yourself. The drive unit
must be repaired only by qualified experts and only
with original spare parts. This will ensure that the safe-
ty of the drive unit is maintained. Unauthorized opening
of the drive unit will void warranty claims.

All components attached to the drive unit and all
other components of the eBike drive (e.g., the chain-
wheel, chainwheel seat, pedals) may be replaced
only with identical components or components spe-
cifically approved for your eBike by the bicycle man-
ufacturer. This protects the drive unit against overload
and damage.

Remove the battery pack from the eBike before begin-
ning work (e.g. inspection, repair, assembly, mainte-
nance, work on the chain, etc.) on the eBike, trans-
porting it by car or plane, or storing it. Unintentional
activation of the eBike system poses a risk of injury.

The eBike system can switch itself on when the eBike
is pushed backwards.

Using the walk assistance function is only recom-
mended when pushing the eBike. There is risk of injury
if the wheels of the eBike are not in contact with the
ground while using the walk assistance.

While using the walk assistance, the pedals will
rotate on bikes with back-pedaling function. Due to
the risk of injury, please make sure that your body is a
sufficient distance away from the rotating pedals.

Use only original Bosch battery packs approved for
your eBike by the manufacturer. Using other battery
packs can lead to injuries and pose a fire hazard. When
using other battery packs, the warranty is void and
Bosch shall not assume any liability.

Do not make any modifications to your eBike system
or attach any other products which would be suitable
for increasing the performance of your eBike sys-
tem. Unauthorized modification of the system could
result in death or serious injury.

Please follow all local, state and federal regulations
when registering and using eBikes.

Read and observe the safety warnings and instruc-
tions in all operating instructions of the eBike sys-
tem and your eBike.
English– 4
Bosch eBike Systems 0 275 U07 PDC | (9.5.17)
Product Description and
Specifications
Intended Use
The drive unit is intended only for driving your eBike and
must not be used for other purposes.
Technical Data
Assembly
Inserting and removing the battery pack
To insert or remove the battery pack in/from the eBike, please
read and follow the battery pack operating instructions.
Checking the Speed Sensor
17 Speed sensor
18 Spoke magnet for the speed sensor
The speed sensor 17 and its spoke magnet 18 must be at-
tached in such a way that the spoke magnet, after a turn of
the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the clearance between the speed sensor 17 and the
spoke magnet 18 is too small or too large, or if the speed sen-
sor 17 is not properly connected, the speed indicator will fail,
and the eBike drive unit will operate in the emergency mode.
In this case, loosen the screw for the spoke magnet 18 and
fasten the spoke magnet to the spoke in such a way that it
runs past the mark of the speed sensor at the correct clear-
ance. If the speed is still not being indicated on the speed
indicator after this is done, please contact an authorized
Bosch eBike dealer.
Drive unit Drive Unit Cruise
Article number 0 275 007 065
Rated continuous power W 250
Torque at drive, max. Nm 63
Rated voltage V 36
Operating temperature °F +23...+104
Storage temperature °F +14...+122
Degree of protection IP 54 (dust and splash
water protected)
Weight, approx. lb 8.8
Drive unit Drive Unit CX
Article number 0 275 007 038
Rated continuous power W 250
Torque at drive, max. Nm 75
Rated voltage V 36
Operating temperature °F +23...+104
Storage temperature °F +14...+122
Degree of protection IP 54 (dust and splash
water protected)
Weight, approx. lb 8.8
Bike lights
1)
Voltage, approx.
2)3)
V 6/12
Maximum output
– Front light
– Rear light
W
W
8.4/17.4
0.6/0.6
1) Not possible via the eBike battery pack in all country-specific ver-
sions, depending on the statutory regulations
2) The voltage level is preset and can be changed only by the eBike
dealer.
3) When changing the bulbs, ensure that the bulbs are also compatible
with the Bosch eBike system (ask your eBike dealer) and that the spec-
ified voltage matches. Bulbs must be replaced only with bulbs of the
same voltage.

Incorrectly installed bulbs can be destroyed or cause damage
to the system.
17
18
5 – 17 mm
89