Bosch Performance Line CX, Системное руководство

Страница: 112 / 296

English– 3
0 275 U07 PDS | (21.4.16) Bosch eBike Systems
Operating your Bosch Drive Unit
Safety Rules
Read and understand all safety warnings and
instructions. Failure to follow the warnings be-
low could result in death or serious injury.
Save all safety warnings and instructions for future
reference.
The term “battery pack” used in these operating instruc-
tions refers both to standard battery packs (battery packs
with holder on the bike frame) and to rack-type battery
packs (battery packs with holder in the rear rack/carrier).

Do not open the drive unit yourself. The drive unit
must be repaired only by qualified experts and only
with original spare parts. This will ensure that the safe-
ty of the drive unit is maintained. Unauthorized opening
of the drive unit will void warranty claims.

All components attached to the drive unit and all oth-
er components of the eBike drive (e.g., the chain-
wheel, chainwheel seat, pedals) may be replaced on-
ly with identical components or components
specifically approved for your eBike by the bicycle
manufacturer. This protects the drive unit against over-
load and damage.

Remove the battery pack from the eBike before begin-
ning work (e.g. inspection, repair, assembly, mainte-
nance, work on the chain, etc.) on the eBike, trans-
porting it by car or plane, or storing it. Unintentional
activation of the eBike system poses a risk of injury.

The eBike system can switch itself on when the eBike
is pushed backwards.

Using the walk assistance function is only recom-
mended when pushing the eBike. There is risk of injury
if the wheels of the eBike are not in contact with the
ground while using the walk assistance.

Use only original Bosch battery packs approved for
your eBike by the manufacturer. Using other battery
packs can lead to injuries and pose a fire hazard. When
using other battery packs, the warranty is void and
Bosch shall not assume any liability.

Do not make any modifications to your eBike system
or attach any other products which would be suitable
for increasing the performance of your eBike sys-
tem. Unauthorized modification of the system could re-
sult in death or serious injury.

Please follow all local, state and federal regulations
when registering and using eBikes.

Read and observe the safety warnings and instruc-
tions in all operating instructions of the eBike sys-
tem and your eBike.
Product Description and
Specifications
Intended Use
The drive unit is intended only for driving your eBike and
must not be used for other purposes.
Technical Data
Drive unit Drive Unit Speed
Article number 0 275 007 041
Rated continuous power W 250
Torque at drive, max. Nm 63
Rated voltage V 36
Operating temperature °F +23...+104
Storage temperature °F +14...+122
Degree of protection IP 54 (dust and splash
water protected)
Weight, approx. lb 8.8
Bike lights
1)
Voltage, approx.
2)3)
V 6/12
Maximum output
– Front light
– Rear light
W
W
8.4/17.4
0.6/0.6
1) Not possible via the eBike battery pack in all country-specific
versions, depending on the statutory regulations
2) The voltage level is preset and can be changed only by the eBike
dealer.
3) When changing the bulbs, ensure that the bulbs are also compatible
with the Bosch eBike system (ask your eBike dealer) and that the spec-
ified voltage matches. Bulbs must be replaced only with bulbs of the
same voltage.

Incorrectly installed bulbs can be destroyed or cause damage
to the system.
English– 4
Bosch eBike Systems 0 275 U07 PDS | (21.4.16)
Assembly
Inserting and removing the battery pack
To insert or remove the battery pack in/from the eBike,
please read and follow the battery pack operating instruc-
tions.
Checking the Speed Sensor
17 Speed sensor
18 Spoke magnet for the speed sensor
The speed sensor 17 and its spoke magnet 18 must be at-
tached in such a way that the spoke magnet, after a turn of
the wheel, moves past the speed sensor with a clearance of
at least 5 mm, yet no more than 17 mm.
Note: If the clearance between the speed sensor 17 and
the spoke magnet 18 is too small or too large, or if the
speed sensor 17 is not properly connected, the speed indi-
cator f will fail, and the eBike drive unit will operate in the
emergency mode.
In this case, loosen the screw for the spoke magnet 18 and
fasten the spoke magnet to the spoke in such a way that it
runs past the mark of the speed sensor at the correct clear-
ance. If the speed is still not being indicated on the speed
indicator f after this is done, please contact an authorized
Bosch eBike dealer.
Operation
Initial Operation
Requirements
The eBike system can only be activated when the following
requirements are met:
– A sufficiently charged battery pack is inserted (see bat-
tery pack operating instructions).
– The on-board computer is properly inserted in the hold-
er (see on-board computer operating instructions).
– The speed sensor is connected properly (see “Checking
the Speed Sensor”, page English–4).
Switching the eBike System On/Off
Options for switching on the eBike system:
– If the on-board computer is already switched on when
inserted into the holder, then the eBike system will be
switched on automatically.
– When the on-board computer and the eBike battery
pack are inserted, briefly press the On/Off button of the
on-board computer once.
– When the on-board computer is inserted, press the
On/Off button on the battery pack.
Once it is switched on, the eBike system is in the “OFF”
mode. Select the desired assistance level and take off.
The drive is activated as soon as you put pressure on the
pedals. The assistance level depends upon the on-board
computer settings.
As soon as you stop pedaling when in normal operation, or
as soon as you have reached a speed of 28 mph, the assis-
tance from the eBike drive unit is switched off. The motor
assistance is automatically re-activated as soon you start
pedaling again and the speed is below 28 mph.
Options for
switching off the eBike system:
– Press the On/Off button of the on-board computer.
– Switch the eBike battery pack off by using its On/Off
button (see battery pack operating instructions.)
– Remove the on-board computer out of its holder.
If the eBike is not moved
and no button is pressed on the
on-board computer for 10 minutes, the eBike system will
shut down automatically in order to save energy.
eShift (optional)
eShift is the integration of automatic gear shifting systems
into the eBike system. The eShift components are electri-
cally connected to the drive unit by the manufacturer. The
operation of automatic gear shifting systems is described in
the operating instructions of the on-board computer.
17
18
5 – 17 mm
112