Bosch FPA-1200-MPC Скачать руководство пользователя страница 46

Страница: 46 / 94

en | Fire alarm

Panel Controller

F.01U.076.969 | 6.0 | 2010.04

Operation guide

Bosch Sicherheitssysteme GmbH

9.6

Triggering fire verification

9.6.1

Alarm verification

The transmission of the alarm is delayed. The alarm message must be checked to ensure it is

correct in the place where the detector generating the alarm is located.

An internal buzzer sounds on the panel. The signaling devices (e.g. sirens) and transmission

device to the fire department are not activated.

The time for checking the fire alarm is called the time to investigate. The duration of this time

can be different for every logical zone. The time to investigate is started if the fire alarm is

confirmed on the panel within the time to acknowledge.

If a real fire alarm is detected during the on-site inspection, the alarm must be forwarded to

the fire department; see

Section 9.6.3 Triggering alarm manually, page 47

. Alternatively, a

manual call point can be triggered at the location.

If it is a false alarm, the triggering detector can be reset or bypassed; see resetting alarm

message or bypassing detectors.

9.6.2

Starting time to investigate

If there is the possibility of testing, the following time spans are displayed. The counters

count to zero:

–

Time to acknowledge

The alarm must be confirmed within the specified time span.

–

Time to investigate

The alarm must be checked within the specified time span. This time

can be specified differently for each logical zone or detector.

–

Reset possible in

: time span after which the detector can be reset. For information on

resetting, see

Section 9.7 Resetting alarm message, page 47

To initiate alarm verification, select

Acknowledge

within the time shown to confirm the alarm.

The time to investigate will be displayed. The alarm verification is initiated.

Test the fire alarm onsite within the specified time.

CAUTION!

If another fire alarm is reported during the time to investigate, all alarm messages are

transmitted to the fire department. The time to investigate is canceled.

CAUTION!

Alarm messages from bypassed detectors are no longer displayed; only faults in these

detectors are displayed.

CAUTION!

The time to investigate is canceled if another alarm is reported within this time. Depending on

the configuration, all alarm messages are forwarded to the fire department in this case.

CAUTION!

If the time to acknowledge or the time to investigate is exceeded, the alarm is immediately

forwarded to external stations.

CAUTION!

If the alarm is not confirmed within this time, it will be forwarded to external stations.

Содержание FPA-1200-MPC































































































Результаты поиска

Содержание FPA-1200-MPC

Отзывы:

Похожие инструкции для FPA-1200-MPC

Бренды по названию

Популярные бренды

Bosch FPA-1200-MPC, Руководство по эксплуатации

Результаты поиска

Содержание FPA-1200-MPC

Отзывы:

Похожие инструкции для FPA-1200-MPC

Бренды по названию

Популярные бренды