Bosch FPA-1200-MPC Скачать руководство пользователя страница 23

Страница: 23 / 94

Panel Controller

In overview | en

Bosch Sicherheitssysteme GmbH

Operation guide

F.01U.076.969 | 6.0 | 2010.04

Status bar

This status bar is available on each menu. In addition, other status bars are offered in some

menus; see also

Section 5.10 Switching between status bars, page 33

The leading number specifies the number of elements in the respective state:

In addition it is possible to display an overview of the type and nature of all message types

received by the panel:

To display the individual elements, touch the relevant field with your finger.

The

Control

and

Trouble

status fields are identified by the letters "B" and/or "C":

–

"B" means that controllers for type B fire safety equipment (G-B) are affected (e.g.

control elements without acknowledgement).

–

"C" means that controllers for type C fire safety equipment (G-C) are affected (e.g.

extinguishing systems).

4.4

Standby display

If the panel is in standby mode, the standby display is shown.

On the standby display, the following information is displayed:

–

Date

–

Time

Depending on the configuration, additional information may be displayed.

In a networked fire detection system, further icons can be displayed in the standby display

depending on the network setting; see

Section 6 Networked panels, page 34

Fire

Control

Trouble

Bypass

Status

Fire

Elements that have triggered a fire alarm

Control

Elements that are activated

Trouble

Elements that have reported a fault

Bypass

Bypassed or isolated elements

Status

Display of a list of the various message and status types and the

number of elements in the respective state

NOTICE!

The display changes from each menu element to the standby display if no entries are made

within ten minutes.

If a gray display is shown, gently touch the touch screen to show the standby display

Night mode

Day mode

Содержание FPA-1200-MPC































































































Результаты поиска

Содержание FPA-1200-MPC

Отзывы:

Похожие инструкции для FPA-1200-MPC

Бренды по названию

Популярные бренды

Bosch FPA-1200-MPC, Руководство по эксплуатации

Результаты поиска

Содержание FPA-1200-MPC

Отзывы:

Похожие инструкции для FPA-1200-MPC

Бренды по названию

Популярные бренды