Bosch CCS 800 Ultro Скачать руководство пользователя

Страница: 26 / 36

Bosch Security Systems B.V. | 2007-08

CCS 800 Ultro

| Installation and Operating Manual

| 26

Troubleshooting

Temporary no microphone reaction, and no sound or

distorted sound from unit loudspeakers

•

Possible cause

Trunk-line overload.

•

Solution

Reduce load on the trunklines by reducing the
number of units, and/or the length of the trunk
cables.

Acoustic Feedback

•

Possible cause

Loudspeaker volume too loud.

•

Solution

Reduce gain using volume control for delegate/
chairman unit loudspeakers on CU.

If available, switch on Digital Acoustic Feedback
Suppression.

•

Possible cause

Distance between units too small (microphone to
loudspeaker of other units).

•

Solution

Increase distance between units.

If available, switch on Digital Acoustic Feedback
Suppression.

•

Possible cause

Too close to microphone units, when using open
headphones.

•

Solution

Increase the distance between headphone and
microphone or disconnect headphones when not
in use.

If available, switch on Digital Acoustic Feedback
Suppression.

Part of system not working

•

Possible cause

Interrupted trunk-line cabling.

•

Solution

Check the trunk-line cabling connections between
the units and the CU, also use the test function on
the CU.

No sound via delegate/chairman loudspeakers

•

Possible cause

Insertion switch in wrong position.

•

Solution

Check if insertion switch at the rear of the CU is in
position "1".

•

Possible cause

Volume control position.

•

Solution

Check if the volume control for delegate/chairman
loudspeakers on the CU is not in the fully counter
clockwise position.

•

Possible cause

Microphone active or headphone connected.

Note

Units with active microphone or connected

headphone(s) have their loudspeakers switched

off.

Содержание CCS 800 Ultro





































Результаты поиска

Содержание CCS 800 Ultro

Отзывы:

Похожие инструкции для CCS 800 Ultro

Бренды по названию

Популярные бренды

Bosch CCS 800 Ultro, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CCS 800 Ultro

Отзывы:

Похожие инструкции для CCS 800 Ultro

Бренды по названию

Популярные бренды