Bosch Ascenta SHE4AM12U Скачать руководство пользователя страница 47

Страница: 47 / 50

Error Code LED's --

DW Symptoms

(seen

Error Code Display

(from cs

Solution

during wash cycles)

test program)

Active / Clean / Sanitized

Make sure water inlet valve isn't stuck "open".

Water doesn’t fill & drain
pump runs

(cont)

Check float switch and wire harness (to power module).

Aqua sensor doesn't run
during wash cycle

E:28

aqua sensor not

properly calibrated

Check continuity between aqua sensor

(I4)

and power module harness

connector.

Make sure aqua sensor is clean where it enters the sump.

If electrical connections are good and the aqua sensor is clean, replace
the aqua sensor.

No power

House wiring isn't 120V

Check house wiring connections and if supply voltage is

≈

98 - 120VAC

to power module harness connector.

Open "On/Off"

"Start"

switch

Check "On/Off" switch & power module connections.

Measure "On/Off" switch resistance. If it’s ‘

∞

Ω

in "on" position, replace

it.

If only drain pump is running, check if float switch has operated

(see

E:15 error code above)

If no LED’s flash when “On/Off” switch is pressed and the dishwasher
door is open, replace operating module (in fascia panel).

Dispenser not operating

Make sure dispenser detergent door isn't jammed.

Detergent dispenser door
jammed

loose wiring

connections

Check connections between rinse-aid dispenser, dispenser actuator

(a2)

and power module harness connector.

Check dispenser actuator operation while running customer service test
program

(steps 15 & 20)

. If actuator operates, but doesn't open

detergent dispenser cover, replace dispenser. If actuator doesn't
operate, replace power module.

Rinse-aid LED is glowing No rinse-aid

loose wiring

connections

Refill rinse aid, if empty.

Check connections between rinse-aid dispenser

(e3)

& operating

module harness connector

(K12)

702_58300000130262_ara_en_c

Page 47 of 50

Содержание Ascenta SHE4AM12U



















































Результаты поиска

Содержание Ascenta SHE4AM12U

Отзывы:

Bosch Ascenta SHE4AM12U, Инструкции по ремонту, Страница: 47 / 50

Результаты поиска

Содержание Ascenta SHE4AM12U

Отзывы: