Bosch AMAX panel 2000 EN ICP-AMAX-P-EN Скачать руководство пользователя страница 21

Страница: 21 / 92

AMAX panel 2000 / AMAX panel 2000 EN

User Guide | en

Bosch Sicherheitssysteme GmbH

Installation Manual

F.01U.241.127 | V4 | 2011.12

Keypad sounds

Table 4.3

Keypad sounds

Sound indicator

Definition

One short beep

A keypad button has been pressed.

One single one-

second beep

The requested operation is refused. Incorrect operation signal.

Two short beeps The system accepted the code. The system executed the requested

function.

One short beep

per second

In walk test mode.

One short beep

every two

seconds

Exit time started.

Continued

sound

–

Last 10s on exit time

–

Keypad fault/tamper sound (fault/tamper to be acknowledged)

–

Keypad alarm sound

Continuous 0.5

second beep,

stops 0.5

seconds

Entry delay time (until alarm ends or system is disarmed).

Содержание AMAX panel 2000 EN ICP-AMAX-P-EN





























































































Результаты поиска

Содержание AMAX panel 2000 EN ICP-AMAX-P-EN

Отзывы:

Bosch AMAX panel 2000 EN ICP-AMAX-P-EN, Руководство по установке, Страница: 21 / 92

Результаты поиска

Содержание AMAX panel 2000 EN ICP-AMAX-P-EN

Отзывы: