Bosch Rexroth MCR 30 Series Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 56

background image

General instructions on damage to equipment and the product 13/56

RE 15215-01-B/11.2015, MCR Series 30, 31, 32, 33 and 41,

Bosch Rexroth AG

3 General instructions on damage to

equipment and the product

The following instructions apply for chapters 6 to 14.

NOTICE

Danger from improper handling!

Product can be damaged!

▶

Do not expose the product to an impermissible mechanical load.

▶

Never use the product as a handle or step.

▶

Do not place/lay any objects on the product.

▶

Do not strike the drive shaft of the radial piston motor.

▶

Do not set/place the radial piston motor on the fittings.

▶

Do not strike fittings (e.g. sensors or valves).

▶

Do not strike sealing surfaces (e.g. service line ports).

▶

Leave the protective covers on the radial piston motor until shortly before the
lines are connected.

▶

Disconnect all electrical connectors before performing electro-welding
or painting operations.

▶

Make sure that the electronics are not electro-statically charged
(e.g. for painting operations).

Damage to equipment due to improper lubrication!

Product can be damaged or destroyed!

▶

Never operate the radial piston motor with insufficient hydraulic fluid. Make sure
in particular that the rotary group has sufficient lubrication.

▶

When commissioning a machine/system, make sure that the case interior and
the service lines of the radial piston motor are filled with hydraulic fluid and
remain filled during operation. Air intrusions in the forward drive shaft bearing
are to be prevented, especially with the installation position "drive shaft
upwards".

▶

Check the hydraulic fluid level in the case regularly and replenish if necessary.
This is particularly important with an above-reservoir installation, where after
long stationary periods the case fluid may drain via the drain line which will
leave the bearings insufficiently lubricated during start up.

Mixing of hydraulic fluids!

Product can be damaged!

▶

Before installation, remove all fluids from the radial piston motor to prevent
contamination of the hydraulic fluid used in the machine/system.

▶

Mixing of hydraulic fluids from different manufacturers or different types from
the same manufacturer is not advisable.

«
...
11
12
13
14
15
...
»

Содержание MCR 30 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для MCR 30 Series

Бренд: ABB Страницы: 8

Бренд: Jabiru Страницы: 201

Бренд: Jabiru Страницы: 103

Бренд: BAFANG Страницы: 4

Бренд: Scania Страницы: 83

Motorcycle Accessories

Бренд: S&S Cycle Страницы: 20

44 A FOUR-35C THREE

Бренд: Westerbeke Страницы: 61

Бренд: DELTA DORE Страницы: 16

Бренд: Kubota Страницы: 309

Бренд: GR Страницы: 8

Бренд: Bison Страницы: 19

Бренд: Nouvag Страницы: 8

Бренд: STG-BEIKIRCH Страницы: 9

Бренд: Vanguard Страницы: 124

Бренд: O.S. engine Страницы: 22

Бренд: O.S. engine Страницы: 29

Бренд: sati Страницы: 19

Бренд: Volvo Penta Страницы: 116

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды