Bosch Rexroth MCR 30 Series Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 56

background image

42/56 Commissioning

Bosch Rexroth AG

, MCR Series 30, 31, 32, 33 and 41, RE 15215-01-B/11.2015

8.4 Final checks

After the running-in phase confirm the following conditions:

▶

Case drain pressure < 10 bar.

▶

Minimum pressure at ports

A

and

B

> 15 bar (general rule) or exact value as

stated in the data sheet, to avoid cavitation.

▶

Holding brake release pressure > 15 bar and < 30 bar (standard specification)
or exact values as stated on the installation drawing for all non-standard
specifications (SO versions).

▶

2 speed switching pressure:
For minimum and maximum 2 speed switching pressures refer to the appropriate
motor installation drawing.

▶

Case drain oil temperature < 85 °C. For operation above this temperature please
consult Rexroth engineering department in Glenrothes.

▶

Operating speeds, pressures and drive power are within current data sheet
recommendations.

«
...
40
41
42
43
44
...
»

Содержание MCR 30 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для MCR 30 Series

Бренд: ABB Страницы: 8

VLT AutomationDrive FC 300 Series

Бренд: Danfoss Страницы: 56

Бренд: Danfoss Страницы: 2

Бренд: Beta Marine Страницы: 88

E-II SGM H Series

Бренд: YASKAWA Страницы: 408

MULTI-VANE 1800 Series

Бренд: Ingersoll-Rand Страницы: 12

Бренд: Saito Страницы: 2

Бренд: Evolution Technologies Страницы: 12

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: Bodine Страницы: 8

Бренд: Magnetic Страницы: 24

Бренд: Dietz Страницы: 10

Бренд: Dietz Страницы: 11

Бренд: Briggs & Stratton Страницы: 200

RolloTube S-line Sun DuoFern

Бренд: RADEMACHER Страницы: 2

Бренд: HIFEI Technology Страницы: 2

Бренд: Yanmar Страницы: 240

Бренд: Yanmar Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды