Bosch Rexroth MCR 30 Series Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 56

background image

Installation 31/56

RE 15215-01-B/11.2015, MCR Series 30, 31, 32, 33 and 41,

Bosch Rexroth AG

7.4 Installing the radial piston motor

7.4.1 Preparation

1.

Check the delivery contents for completeness and transport damage.

If the part number on the motor identification label (chapter 5.4) does not
correspond to the order confirmation, contact the Bosch Rexroth sales partner
for clarification.

L

B

A

R

Port

B

Port

A

Fig. 18: Direction of rotation

View motor from shaft with ports uppermost and pressurising port

B

:

L

Counter-clockwise

R

Clockwise

The direction of rotation is specified in the motor description on the identification
label (chapter 5.3).
Letter "L" in code, or no designation, means counter-clockwise rotation.
Letter "R" in code means clockwise rotation.

7.4.2 Dimensions

The installation drawing specifies the dimensions of the mountings and ports of the
radial piston motor.

7.4.3 General instructions

During installation (and removal) of the radial piston motor, observe the following
general instructions and handling instructions:

•

The radial piston motor should be installed using suitable fasteners which have the
capacity to safely withstand the expected loads and torque.

•

The permissible axial and radial loading on the drive shaft is specified in the
relevant motor data sheet.

•

To minimise noise levels ensure connecting lines are isolated by use of anti-
vibration mountings.

•

Make sure that the installation location is clean and free from contamination.

«
...
29
30
31
32
33
...
»

Содержание MCR 30 Series

























































Отзывы:

Нет отзывов

Похожие инструкции для MCR 30 Series

Бренд: Fagor Страницы: 174

Бренд: Continental Motors Страницы: 146

Walker Ford / Lehman

Бренд: AirSep Страницы: 4

Бренд: ACME motori Страницы: 23

Бренд: HARTFORD Страницы: 70

Бренд: SICK Страницы: 20

Бренд: MINN KOTA Страницы: 3

Бренд: MINN KOTA Страницы: 4

HYDRO-FORCE 65043

Бренд: Bestway Страницы: 8

Бренд: Toro Страницы: 96

Бренд: VM Страницы: 108

Бренд: Yanmar Страницы: 160

Бренд: NANOTEC Страницы: 295

Бренд: TOHATSU Страницы: 87

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды