Bolin Technology DANTE AV D Series Скачать руководство пользователя | Manualshive

Страница: 30 / 47

background image

30

Audio Routing

Camera Audio

Bolin Dante AV PTZ camera has audio input via Mic/Line-in port that is on the back panel of the camera.

•

Audio input signal can be embedded with the camera local HDMI output.

•

Audio input signal can be embedded with the camera Dante AV IP video streaming.

•

As an audio TX endpoint within Dante AV network, the camera Mic/Line-in audio signal can be
independently routed to any Audio RX endpoints.

•

The 'Left' and 'Right' audio channels on the AVIO USB audio receiver are subscribed to the 'Left' and 'Right'
Tx channels on the Bolin-PTZ-Camera-D220 audio transmitter.
These subscriptions would cause the left and right audio channels from the Bolin-PTZ-Camera-D220 audio
transmitter to be output via the USB of AVIO.

«
...
28
29
30
31
32
...
»

Содержание DANTE AV D Series
















































Отзывы:

Нет отзывов

Похожие инструкции для DANTE AV D Series

Lumix H-FSA14140

Бренд: Panasonic Страницы: 26

Lumix H-HS12035

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 2

H-FS045200 - Lumix Telephoto Zoom Lens

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 18

FL500 - DMW - Hot-shoe clip-on Flash

Бренд: Panasonic Страницы: 44

E-1 - Digital Camera SLR

Бренд: Olympus Страницы: 2

Бренд: Okina Страницы: 3

Бренд: Z-EDGE Страницы: 4

X-560WP - Digital Camera - Compact

Бренд: Olympus Страницы: 66

Бренд: Olympus Страницы: 184

Бренд: Olympus Страницы: 94

102375 - Stylus Epic Zoom 80 DLX 35mm Camera

Бренд: Olympus Страницы: 67

Бренд: Olympus Страницы: 166

Бренд: Zavio Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды