BOGBALLE L15 base Скачать руководство пользователя страница 84

Страница: 84 / 96

Position

Component

Instruction

Cross joint and lock of the PTO

Use grease

Adjustment axle (cross axle w/ 4 bearings)

Use oil

Setting handle (axle w/ 2 bearings)

Use oil

Connection rods (rods between axle and shutters)

Use oil

Agitator R and L (under cone)

Use grease

Please notice that high pressure from too much oil/grease will restrict the rotation of the agitator bearing. In such a

case the lubricator nipple must be demounted to release the pressure.

Spreading vanes

●

The vanes must be considered as a wearing part.

●

Change the vanes if they are deformed or if they are worn and have holes.

●

All nuts and bolts of the spreader must be retightened after the first 5 to 8 hours of operation

(see page 11)

NOTE:

The bolts in the central and angle gears are locked with lock-tite and do not need retightening. Stainless

nuts and bolts may fuse together - the thread must be greased with cutting lubricant graphite or copper grease.

Nuts and bolts

Lubrication

The components below must be lubricated according to below instruction.

Maintenance and care

Содержание L15 base

































































































Результаты поиска

Содержание L15 base

Отзывы:

Бренды по названию

Популярные бренды

BOGBALLE L15 base, Руководство оператора

Результаты поиска

Содержание L15 base

Отзывы:

Бренды по названию

Популярные бренды