background image

This product is compatible 
with strollers that have a serial 
number within the range 
listed. Using this product on 
strollers with incompatible 
serial numbers may lead 
to injury or death.

Main Bar

Right Tray

Arm

Restraint Belt M

Accessory Bar

Left Tray

Bonnet Spacer 2x

Restraint Belt F

Sharp Screw 2x

Pivot Nut 2x

Pivot Screw 2x

Arm

Loctite 262

Pivot Plug 2x

Bonnet Screw 2x

TAKE TIME - READ AND UNDERSTAND INSTRUCTIONS COMPLETELY!

Before attempting to assemble or use your new Duallie ICSA, read and understand these assembly 
instructions completely, as well as the warnings at the end of this document, to insure proper 
assembly and safe operation.

If you are unclear on any point, contact your dealer or BOB before use.

Duallie Infant Car Seat 
Adapter Instructions

TOOLS NEEDED:

To perform the 
installation, you need a 
Phillips screwdriver, 4mm 
hex (Allen) wrench, an 
8mm socket wrench and 
a rag or paper towel. 

Congratulations on 
your purchase of the 
BOB Duallie Infant Car 
Seat Adapter (ICSA). It 
is designed to allow the 
attachment of an Infant Car 
Seat to your BOB Duallie 
Stroller. Please refer to the 
tables at right for details 
of compatible strollers and 
car seats.

Car Seat Compatibility

Brand

Model

Year (s)

Britax

Companion ™

2003-2008

Graco

®

Snug Ride

®

2003 and newer

Graco

®

Snug Ride

®

 30

2010 and newer

Graco

®

Snug Ride

®

 32

2008 and newer

Graco

®

Snug Ride

®

 35

2009 and newer

Graco

®

Safe Seat ™

2006 and newer

Peg Perego

®

Primo Viaggio™

2003 and newer

Peg Perego

®

Primo Viaggio SIP™

2006 and newer

Peg Perego

®

Primo Viaggio SIP™ 30/30 2007 and newer

BOB

®

 Stroller Compatibility

Model

Serial Number Range

Duallie

®

AD000001 - AD999999

Ironman

®

 Duallie

AE000001 - AE999999

Revolution

®

 Duallie

AH000001 - AH999999

Revolution Duallie 12"

AL000001 - AL999999

Stroller Strides

®

 Duallie

AM000001 - AM999999

OMA18B

P1

Содержание Duallie Infant Car Seat














Отзывы: