manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Руководство пользователя для мотоциклиста

Поделиться
Скачать
BMW Motorrad R 1200 RT 2005 Скачать руководство пользователя страница 77

Parking your motorcy-
cle
Placing on side stand

If the ground is soft or
uneven, there is no guar-

antee that the motorcycle will
rest firmly on the stand.
Always check that the ground
under the stand is level and
firm.

Switch off the engine.
Pull the handbrake lever.
Hold the motorcycle upright
and balanced.
Use your left foot to extend
the side stand fully (arrow).

The side stand is de-
signed to support only

the weight of the motorcycle.
Do not lean or sit on the mo-
torcycle with the side stand
extended.

Slowly lean the motorcycle
to the side until its weight
is taken by the stand and
dismount to the left.

When you prop the
motorcycle on the

side stand, the surface of
the ground will determine
whether it is better to turn the
handlebars to the left or right.
However, the motorcycle
is more stable on a level
surface with the handlebars
turned to the left than with
the handlebars turned to the
right.
On level ground, always turn
the handlebars to the left to
set the steering lock.

Turn the handlebars to the
full left or right lock position.
Check that the motorcycle
is standing firmly.

On a grade, the motor-
cycle should always face

uphill; select 1st gear.

5

75

z

Riding

Содержание R 1200 RT 2005












































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды