manualshive.com logo in svg

BMW Motorrad R 1200 RT 2005, Руководство пользователя для мотоциклиста

Поделиться
Скачать
BMW Motorrad R 1200 RT 2005 Скачать руководство пользователя страница 37

Switch off Ignition, then op-
erate handbrake lever and
footbrake lever consecutive-
ly.
The following functions
must be available:
Brake pressure present at
both brake levers.
Brakes acting on both
wheels.
No escaping brake fluid is
visible.

There is a defect in the
brake system that can

lead to reduced braking ac-
tion.
Brake early.

If these criteria are satis-
fied, you can continue rid-
ing. However, bear in mind
that a loss of brake fluid that
cannot be detected might
be the cause of the warn-
ing.

Have the fault rectified as
soon as possible by a spe-
cialized workshop, prefer-
ably an authorized BMW
motorcycle retailer.

If a fault has been determined
during the operating and leak
test:

There is a defect in the
brake system that can

lead to accidents.
Do not continue driving.

You may not continue driv-
ing.
Inform a specialized work-
shop, preferably an autho-
rized BMW motorcycle re-
tailer.

ABS error

General warning light
flashes red four times

per second.

ABS warning light flash-
es four times per sec-

ond.

At least two faults have oc-
curred in the brake system. In
a least one brake circuit only
the residual braking function
is available and the fluid lev-
el in the brake system is too
low.

See the fault descriptions
above.

3

35

z

Status indicators

Содержание R 1200 RT 2005












































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды