BMW Motorrad R 1200 RT 2005 Скачать руководство пользователя страница 110

Страница: 110 / 171

ably an authorized BMW mo-
torcycle retailer.

During the following
work, parts of the front

brake, in particular of the
BMW Integral ABS, can be
damaged.
Take care not to damage the
brake system, in particular the
ABS sensor with cable and
the ABS sensor ring.

The front wheel must be
installed right way round

to rotate in the correct direc-
tion.
Observe the direction of rota-
tion arrows on the tires or on
the rim.

Mount spacing bushing on
left side on wheel hub.

Roll the front wheel into the
front wheel guide.
When rolling in wheel,
watch ABS sensor on left
side.

Install quick-release axle

with torque.
Quick-release axle in axle
mount
37 lb/ft
Install axle clamping
screw

with torque.

Clamping screw for quick-
release axle
14 lb/ft
Remove front wheel stand.
Ease the brake calipers on
to the brake disks.

108

Maintenance

Содержание R 1200 RT 2005












































































































































































Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды

BMW Motorrad R 1200 RT 2005, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды