BMW Motorrad R 1200 RT 2005 Скачать руководство пользователя страница 73

Страница: 73 / 171

self-diagnosis has been
performed.

Emergency ON/OFF
switch

in operating

position

Switch on the ignition.
Pre-ride check is
performed. (

71)

ABS self-diagnosis is per-
formed. (

72)

Press the starter button

At extremely low tem-
peratures it may be nec-

essary to operate the throt-
tle twist grip during starting.

At ambient temperatures be-
low 32 °F (0 °C), actuate the
clutch after switching on the
ignition.

The start attempt is au-
tomatically interrupted

if battery voltage is too low.
Recharge the battery before
you start the engine, or use
jump leads and a donor bat-
tery to start.

The engine starts.
If the engine fails to start,
the troubleshooting table in
the chapter "Technical Da-
ta" may provide assistance.
(

134)

Pre-ride check

After switching on the igni-
tion, the instrument cluster
carries out a general warn-
ing light test. In the process
the warning light first lights
up yellow and then red for
checking. This test, called

a "Pre-ride check", is indicat-
ed by the lettering

CHECK!

in the display. With the OE
cruise control, the

SET

light

is also displayed. If the en-
gine is started during the test,
the test is canceled.

Phase 1

General warning light
lights up yellow.

The note

CHECK!

is indi-

cated.

Phase 2

General warning light
lights up red.

The note

CHECK!

is indi-

cated.

With OE cruise control,
cruise-control indicator

light lights up.
If the general warning light is
not shown:

Riding

Содержание R 1200 RT 2005












































































































































































Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды

BMW Motorrad R 1200 RT 2005, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды