BMW Motorrad R 1200 RT 2005 Скачать руководство пользователя страница 55

Страница: 55 / 171

switched on longer than
absolutely necessary.

Switching on low-beam
headlight

The low-beam headlight
switches on automatically
when you start the engine.

With the engine switched
off, you can switch on

the lights by switching on the
high-beam headlight with the
ignition switched on or by op-
erating the headlight flasher.

Switching on high-beam
headlight

Press top part of switch

for high-beam headlight.
High-beam headlight
switched on.
Move switch

for high-

beam headlight to center
position.
High-beam headlight
switched off.
Press bottom part of
switch

for the high-beam

headlight.
High-beam headlight is
switched on as long as

switch is pressed (headlight
flasher).

Switching on side lights

Switch off the ignition.

You can switch on the
parking lights only imme-

diately after switching off the
ignition.

Press and hold the left turn
indicator switch

until side

light is switched on.

Switching off side lights

Switch on the ignition.
Side lights switched off.

Operation

Содержание R 1200 RT 2005












































































































































































Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды

BMW Motorrad R 1200 RT 2005, Руководство пользователя для мотоциклиста

Результаты поиска

Содержание R 1200 RT 2005

Отзывы:

Бренды по названию

Популярные бренды