BlueBox Datatech Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 56

background image

17

We reserve the right to make changes without any prior notice.

Translation from original instructions

3.3.2 Units with separate ventilation section

The same means used for the unit can be employed to handle the fan section.

3.4 Storage

The units are built to be installed in indoor environments.

Storage outdoors is not allowed. Upon receipt they must be put in locations protected from weather agents.
Since the remote condensing unit is designed to be installed outdoors, it can withstand outdoor atmospheric conditions.
For the condensing unit, must be pay attention to the place where it is placed, which must be on the flat, in order to avoid

deformation of the structure with consequent possible breakage.

«
...
15
16
17
18
19
...
»

Содержание Datatech

























































Отзывы:

Нет отзывов

Похожие инструкции для Datatech

Бренд: Olimpia splendid Страницы: 154

Бренд: Olimpia splendid Страницы: 26

Бренд: Olimpia splendid Страницы: 100

Бренд: Olimpia splendid Страницы: 44

Бренд: Olimpia splendid Страницы: 80

bycool DINAMIC 1.2

Бренд: dirna Bergstrom Страницы: 100

Бренд: Omega Страницы: 56

Бренд: Soleus Air Страницы: 29

OTEC IEFC-D Series

Бренд: Omega Страницы: 12

Бренд: EAS Electric Страницы: 199

USB Deluxe Air Purifier

Бренд: Wagan Страницы: 20

Бренд: thermital Страницы: 24

Бренд: REMKO Страницы: 20

Бренд: Gree Страницы: 112

Бренд: Gree Страницы: 18

Бренд: Payne Страницы: 6

Бренд: Friax Страницы: 20

Бренд: Coleman Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды