background image

100

ProxySG 900 Series Maintenance & Upgrade Guide

Slide Rail Kit

Install the Appliance into the Equipment Rack

This procedure describes how to mount the Blue Coat ProxySG 900 series appliance into the 
newly installed slide-rails in the equipment rack.

!

WARNING! DO NOT 

attempt to mount theBlue Coat ProxySG 900 series appliances alone! 

If a mechanical lift is not used, Blue Coat recommends two people install the 
Blue Coat ProxySG 900 series appliances.

To install the appliance into the equipment rack:

1.

Align the grooves of the inner rail with those on Rail_A and slide the appliance half-way 
into the rack. 

2.

Activate the white tab on the inner rail to slide the appliance fully into the equipment 
rack.

3.

Tighten the rack screws securing the rail mounting brackets.

• For 4-post installations, the Rail_A and Rail_C brackets must be tightened.

• For 2-post mid mount installations, tighten both sets of Rail_B brackets.

• For 2-post front mount installations, tighten the Rail_A and Rail_B brackets.

4.

Tighten the thumbscrews on the retaining ears to secure the unit from sliding out of the 
equipment rack.

e

TIP:

 The slide release latches can be activated by pushing 

or

 pulling the latch.

Содержание ProxySG SG900-10









































































































Отзывы: