Blizzard B74C Скачать руководство пользователя | Manualshive

Страница: 15 / 52

background image

ASSEMBLY

OM 0410SB-A

13

T

RACTOR

P

REPARATION

See Dealer for Tractor Preparation information.

S

NOWBLOWER

A

SSEMBLY

The snowblower is assembled at the factory except for the parts in the hardware bag provided with the
snowblower, the chute and the options if appropriate. Use the present manual and lay out all parts for
assembly. Separate bolts and nuts into various sizes. After assembly, torque all the bolts according to the

Torque Specification Table

at the end of manual.

Installation of the Chute

(Figure 1)

1. Figure 1:

Place the rotation bushing (item 1)

on the chute base of the snowblower.

2. Figure 1:

Install the chute (item 2) over the

rotation bushing and install the three 3/16"
spacers (item 3) and the 3/8" spacers (item 4).

3. Figure 1:

Insert the two three holes retaining

plates (item 5) by placing the large section
toward the support of the hydraulic motor.
Secure with two 1/2"NC x 3/4" carriage bolts
(item 7), upside down (front of the chute) and the
four other bolts head up (rear of the chute).
Secure with six 1/2" lockwashers (item 8) and
four 1/2"NC hex nuts (item 9).

4.

Tighten all bolts according to the

Torque

Specification Table

at the end of the manual.

Figure 1

«
...
13
14
15
16
17
...
»

Содержание B74C





















































Отзывы:

Нет отзывов

Похожие инструкции для B74C

Бренд: Ryobi Страницы: 20

Бренд: Yard-Man Страницы: 28

Бренд: Echo Страницы: 32

Бренд: Kärcher Страницы: 5

Бренд: Kärcher Страницы: 104

Бренд: ebm-papst Страницы: 11

Бренд: ebm-papst Страницы: 10

Бренд: Ryobi Страницы: 46

Groundsmaster 200 Series

Бренд: Toro Страницы: 20

Бренд: White Outdoor Страницы: 20

Бренд: Kongskilde Страницы: 60

Бренд: VITO GARDEN Страницы: 40

Бренд: Worx Страницы: 24

Aerocore Turbo Blower CBV60H1.9

Бренд: Masport Страницы: 8

Бренд: Stiga Страницы: 30

Бренд: Stiga Страницы: 33

Бренд: Elektror Страницы: 52

Бренд: Western Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды